MG ZS EV Charging at Atlante

MG ZS EV Charger Won't Start? Quick Fix Guide

You have connected the charger to your MG ZS EV but nothing happens. No power flowing, the charger is showing an error, or the car just does not respond. Before you give up and drive to another station, run through these checks. Most charging failures have a simple fix.

Symptoms

• Charger display shows error after plugging in the CCS2 connector
• Charge port light on the ZS EV does not illuminate
• Car dashboard shows no indication of charging activity
• Charger screen stays on the welcome or authentication screen
• Type 2 AC connector locks in but charging does not begin

What to Do

1. 1

   Check the charger display for errors or instructions

   Look at the charger screen. It will tell you if authentication is needed, if there is a fault, or if it is waiting for the vehicle. This is the fastest way to identify the problem.

2. 2

   Remove and reinsert the connector

   Pull the CCS2 or Type 2 connector out completely, wait 10-15 seconds, and push it back in firmly. Make sure it locks into the ZS EV's front charge port.

3. 3

   Authenticate with the charger

   Tap your RFID card, start the session in the network app, or use contactless payment. Try authenticating both before and after plugging in, as different chargers have different sequences.

4. 4

   Check the charge port for obstructions

   Inspect the ZS EV's charge port for debris, ice, or visible damage to the pins. In winter, gently remove any ice with your hand or a soft cloth. Do not use metal tools.

5. 5

   Turn the car off and back on

   Switch the ZS EV off completely, wait 30 seconds, then turn it on again. This resets the onboard charging system and can resolve communication glitches.

6. 6

   Try another stall or station

   If the charger is faulty, move to another stall. If the entire station is down, find a nearby alternative using your charging app.

MG ZS EV Charging Payment Failed? Solve It Fast

Your MG ZS EV is plugged in and ready to charge, but the payment is not going through. Whether it is an RFID card, an app, or a bank card, payment failures are among the most common reasons charging sessions fail to start. Here is how to get it sorted and get on with your charge.

Symptoms

• RFID card tap produces no response from the charger
• Network app shows a payment declined error
• Contactless card is rejected at the charger terminal
• Charger asks for authentication but nothing you try works
• Charging starts then stops within seconds due to billing error

What to Do

1. 1

   Check what payment methods the charger accepts

   Look at the charger for payment logos, QR codes, or instructions. Identify whether it takes RFID, app payments, contactless cards, or a specific network's card only.

2. 2

   Try the charger network's own app

   Scan the QR code on the charger or search for the network's app. Register, add a payment method, and try starting the session through the app.

3. 3

   Try alternative payment methods

   Switch between RFID card, contactless bank card, and app-based payment. If you have a roaming provider like Plugsurfing or Shell Recharge, try their card or app.

4. 4

   Check your bank for declined transactions

   Open your banking app to look for blocked pre-authorizations or declined charges. If the hold was blocked, you may need to approve it or use a different card.

5. 5

   Try a different stall

   The card reader on one stall may be faulty while others work fine. Move to the next stall and try again.

6. 6

   Find a nearby compatible charger

   If nothing works at this station, use your charging app to find an alternative. Filter by networks where your payment methods are confirmed to work.

MG ZS EV Charging Slowly? Causes and Solutions

Your MG ZS EV is taking much longer to charge than you expected. With a 94kW maximum DC speed and no battery preconditioning, the ZS EV is particularly affected by cold weather and charging conditions. Understanding these limits helps you plan better and avoid frustration at the charger.

Symptoms

• DC fast charging power well below 94kW
• AC charging not reaching the full 11kW
• Very slow charging in cold or winter conditions
• Charging speed drops significantly above 50-60% SOC
• First fast charge of the day is much slower than subsequent ones

What to Do

1. 1

   Verify the charger's maximum output

   Check the charger label or app for its power rating. If it is a 50kW unit, the ZS EV cannot charge faster. Look for chargers rated at 100kW or above to access the full 94kW capability.

2. 2

   Drive longer before charging in cold weather

   Since the ZS EV has no preconditioning, the best way to warm the battery is to drive. A longer highway drive before the charger will raise the battery temperature naturally, improving DC charging speed.

3. 3

   Charge at a lower SOC

   Arrive at the charger between 10-20% SOC for the fastest charging speeds. The ZS EV delivers its best power in the 10-50% range.

4. 4

   Choose a stall without power sharing

   If the station shares power between stalls, pick one where the adjacent stall is empty. This gives you the full power allocation.

5. 5

   Check your AC cable and charger

   For AC charging, verify you are using a 3-phase Type 2 cable on an 11kW charger. A single-phase connection limits you to about 3.6kW.

6. 6

   Accept the winter speed reality

   In cold weather, the ZS EV's lack of preconditioning and heat pump means slow starts are unavoidable. Plan for longer charging stops in winter and consider parking in a heated garage when possible.

New station with teething problems

Atlante is expanding rapidly, and many stations are brand new. Newly installed chargers sometimes have firmware bugs, incomplete network configuration, or hardware that has not been fully tested under real-world conditions.

Symptoms

• Charger turns on but fails to communicate with your vehicle
• Session starts but drops after a few seconds
• Charger screen shows an error code you have never seen before
• Station appears on the map but the chargers are not yet operational

How to Fix It

1. 1

   Try a different charger at the same station

   New stations often have multiple units and the issue may be limited to one charger. Try another unit before giving up on the location.

2. 2

   Unplug, wait 30 seconds, and retry

   New charger firmware sometimes fails on the first handshake but succeeds on the second attempt. A short wait lets the charger reset its session state.

3. 3

   Start the session through the Atlante app

   If the charger's screen or contactless reader is not working properly, the app provides a separate communication path to the charger's backend. This can bypass local hardware issues.

4. 4

   Check the Atlante app for station status notes

   Atlante sometimes posts notices about newly activated stations that are still in testing. The station detail page in the app may show a note about limited functionality.

5. 5

   Report the issue and move to the next station

   Use the Atlante app to report the problem. New station issues are usually fixed quickly once reported. Check the app for the nearest alternative Atlante or competitor station.

App crashes on older phones

The Atlante app can be unstable on older phones or phones running outdated operating systems. The app may crash during login, while loading the map, or in the middle of starting a session.

Symptoms

• App closes unexpectedly when you open the station map
• App freezes during the payment screen
• Login screen loads but the app crashes after entering credentials
• App works briefly but crashes when you try to start a session

How to Fix It

1. 1

   Update the Atlante app to the latest version

   Atlante pushes frequent updates that fix stability issues. Open the App Store or Google Play and check for updates before your trip.

2. 2

   Clear the app cache

   On Android, go to Settings, Apps, Atlante, and clear the cache. On iPhone, delete and reinstall the app. Corrupted cache data is a common cause of crashes.

3. 3

   Check your phone's operating system version

   The Atlante app may require iOS 15+ or Android 10+. If your phone is on an older version, update if possible. If your phone cannot update, you may need a roaming app as a backup.

4. 4

   Use contactless payment as a fallback

   If the app keeps crashing and the station supports contactless, tap your credit or debit card on the charger's payment terminal. Not all Atlante stations have this yet, but it completely bypasses the app.

5. 5

   Try a roaming app

   Apps like Chargemap, Shell Recharge, or Electropass can start sessions at Atlante stations without using the Atlante app. Check roaming coverage before relying on this.

Contactless payment terminal not activated

Atlante is rolling out contactless card payment across its network, but not every charger has an active terminal yet. Some units have the hardware installed but the payment function is not turned on.

Symptoms

• Card reader is visible on the charger but does not respond to a tap
• Screen says 'Use app to start' with no contactless option shown
• Contactless symbol is printed on the charger but the reader light is off
• You see a payment terminal but tapping produces no response

How to Fix It

1. 1

   Download and use the Atlante app

   At stations where contactless is not yet active, the Atlante app is the primary payment method. Download it before your trip and add a payment card in advance.

2. 2

   Check the charger screen for payment instructions

   Some Atlante chargers display which payment methods are currently available. If contactless is not listed, the terminal is not active at that unit.

3. 3

   Try a different charger at the same station

   Contactless activation sometimes rolls out unit by unit. Another charger at the same station may have an active terminal.

4. 4

   Use a roaming RFID card or app

   If you have an RFID card from a roaming provider, try tapping it. Some Atlante stations accept roaming RFID even when the contactless card terminal is not active.

Charger screen hard to read in direct sunlight

Some Atlante charger screens have low brightness levels that make them nearly impossible to read in bright sunlight. This is especially common at stations in Southern Europe during summer.

Symptoms

• Screen content is barely visible outdoors during the day
• You cannot read the price, status, or error messages on the screen
• Screen appears to be off but the charger is actually on
• You have to cup your hands around the screen to read it

How to Fix It

1. 1

   Use your body or hand to shade the screen

   Stand to block direct sunlight from hitting the screen. Even partial shade can make the display readable.

2. 2

   Take a photo of the screen with your phone

   Your phone camera can sometimes capture what your eyes cannot. Take a photo and zoom in to read the text.

3. 3

   Use the Atlante app to monitor your session

   All session information (charging speed, energy delivered, cost, estimated time) is available in the app. You do not need the charger screen to track your session.

4. 4

   Start the session entirely through the app

   If you cannot read the screen at all, use the Atlante app to select the charger, start the session, and stop it when done. This avoids needing to interact with the screen.

Cable connector requires specific angle to lock

Some Atlante charger cables need to be inserted at a particular angle or with extra force for the CCS2 connector to seat properly. If it is not fully locked, the session will not start.

Symptoms

• Connector feels like it is in but the charger does not recognize it
• Charger screen says 'Connect cable' even though the cable is plugged in
• You hear a partial click but the connector is not locked
• Connector slides back out after you let go

How to Fix It

1. 1

   Push the connector straight in, then slightly upward

   Some Atlante CCS2 connectors need a slight upward tilt after the initial push to engage the locking mechanism. You should feel and hear a solid click.

2. 2

   Check for debris in the vehicle's charging port

   Dust, ice, or a small pebble in the port can prevent the connector from seating fully. Inspect the port and brush out anything you find.

3. 3

   Make sure the vehicle is unlocked and ready to charge

   Some vehicles lock the charging port flap or disable the inlet when the car is locked or in drive mode. Ensure the car is in park and unlocked.

4. 4

   Try a different cable if the charger has two

   If the charger has two CCS2 cables, try the other one. One cable may have a slightly worn connector that does not seat as easily.