MG MG5 Charging at GreenWay

MG MG5 Charger Won't Start? Step-by-Step Help

You have plugged in your MG MG5 and the charging session refuses to start. The charger might be blinking, showing an error, or doing nothing at all. This is a common problem across all EVs, and the MG5 is no exception. Most causes are easy to diagnose and fix on the spot.

Symptoms

• Charger display shows an error or stays on the start screen
• CCS2 connector plugs in but charging does not initiate
• MG5 charge port light does not turn on or stays amber
• App shows the charger as available but the session does not begin
• AC Type 2 cable locks in but no power flows

What to Do

1. 1

   Read the charger screen

   Check for error messages, authentication prompts, or status indicators. If it says 'waiting for vehicle' the problem is on the car side. If it says 'error' or 'out of service,' the charger is the issue.

2. 2

   Unplug, wait, and replug

   Remove the connector completely, wait 15 seconds, and reinsert it firmly. Listen for the locking click on the MG5's charge port. This resets the communication handshake.

3. 3

   Complete authentication

   Tap your RFID card, open the network app and start the session, or use contactless payment. Some chargers need you to authenticate before plugging in, others after.

4. 4

   Check for scheduled charging

   Go to the MG5's charging settings on the infotainment screen. If a charging schedule is active, disable it to allow immediate charging.

5. 5

   Restart the car's systems

   Turn the MG5 off using the start button, wait 30 seconds, then turn it back on. This can clear temporary software glitches that prevent the charge port from communicating.

6. 6

   Move to another stall or station

   If the charger is at fault, try another stall. If no stalls work, the station may have a site-wide issue. Find an alternative station using your charging app.

MG MG5 Charging Payment Failed? How to Fix It

You are standing at a charger with your MG MG5 and the payment will not work. Card declined, app throwing errors, or no idea how to pay at all. This is one of the most frustrating parts of public charging, and it happens to everyone. Here is how to get past it.

Symptoms

• RFID card not recognized when tapped on the charger
• Charging app shows payment error or transaction declined
• Contactless card payment rejected at the terminal
• Charger starts authentication but then returns an error
• Session begins but ends immediately due to payment failure

What to Do

1. 1

   Identify accepted payment methods

   Look at the charger for payment logos and instructions. Note whether it accepts RFID cards, specific apps, contactless cards, or QR code payments. Each charger may support different methods.

2. 2

   Try the network's own app

   Download the charger network's app, create an account, and add a payment method. Then start the session through the app. This bypasses RFID and contactless issues.

3. 3

   Switch to an alternative payment method

   If your primary RFID card fails, try contactless with your bank card. If that fails, try a roaming provider like Plugsurfing, Shell Recharge, or Chargemap.

4. 4

   Check your bank for blocked transactions

   Open your banking app and look for declined or pending transactions. If the pre-authorization was blocked, call your bank or temporarily increase your card limit.

5. 5

   Try a different stall

   If the card reader on one stall is broken, another stall at the same station may have a working reader. Try the next one before giving up on the location.

6. 6

   Find an alternative station

   Use your charging app to find a nearby station from a network where your payment methods are confirmed to work. Filter by your preferred payment method if the app supports it.

MG MG5 Charging Slowly? Why and How to Fix It

Your MG MG5 is charging slower than you expected. With a maximum DC speed of 87kW, the MG5 is not the fastest charger in its class, but it should still deliver reasonable speeds. If you are seeing numbers well below that, something else is going on. Here is what to check.

Symptoms

• DC charging power showing well below 87kW on the charger display
• AC charging stuck below 11kW on a capable wallbox
• Estimated charging time significantly longer than expected
• Charging speed drops sharply above 50-60% SOC
• Very slow charging in cold weather conditions

What to Do

1. 1

   Check the charger's maximum power output

   Verify the charger is rated above 87kW. If it is a 50kW charger, the MG5 is getting the maximum available. Look at the charger label or check in the network app.

2. 2

   Use preconditioning in cold weather

   Set the fast charger as your destination in the MG5's navigation system. This activates battery preconditioning, which warms the battery before you arrive and improves initial charging speed.

3. 3

   Check your state of charge

   If you are above 60% SOC, the MG5's charging taper is expected. For the fastest session, arrive at the charger between 10-20% SOC and charge to 70-80%.

4. 4

   Try a different stall to avoid power sharing

   If the station shares power between stalls, wait for other cars to finish or move to a stall that is not paired with another active charger. Some stations label which stalls share power.

5. 5

   For AC, verify your cable and charger

   Make sure you are using a 3-phase Type 2 cable on an 11kW or higher AC charger. A single-phase connection limits you to about 3.6kW, which adds many hours to a full charge.

6. 6

   Check car settings for charging limits

   In the MG5's settings, look for any AC current limit or maximum charge level that might be capping your speed.

App-only payment with no backup option

GreenWay stations require the GreenWay app to start a session. There are no contactless card readers or RFID pads. If the app fails or your phone dies, you cannot charge.

Symptoms

• No card reader or RFID pad visible on the charger
• Charger screen shows a QR code or 'Use app to start' message
• You arrived without the app installed and cannot begin a session
• Your phone battery is low and you are worried it will die during setup

How to Fix It

1. 1

   Download the GreenWay app before your trip

   This is non-negotiable for GreenWay stations. Install the app, create an account, and add a payment method while you have good internet and battery. Do this before you leave, not at the charger.

2. 2

   Charge your phone before arriving at the station

   Since you need your phone to start and monitor the session, make sure it has enough battery. Use your car's USB port or a power bank on the way.

3. 3

   Try a roaming app as a backup

   Some GreenWay stations are accessible through roaming providers like Plugsurfing, Shell Recharge, or Chargemap. Check your roaming app's map to see if the specific station is covered before counting on it.

4. 4

   Scan the QR code on the charger

   If you do not have the app, scan the QR code with your phone camera. It may direct you to the app store or, in some cases, to a web-based session start page.

App requires location services for charger activation

The GreenWay app needs location services turned on to activate a charger. Without it, the app cannot verify that you are at the station and will not let you start a session.

Symptoms

• App shows 'Enable location services' and will not proceed
• You can see the charger on the map but cannot start a session
• The 'Start charging' button is grayed out or unresponsive
• App shows your location incorrectly, placing you far from the station

How to Fix It

1. 1

   Enable location services for the GreenWay app

   Go to your phone settings, find the GreenWay app, and set location access to 'While Using' or 'Always.' On iPhone: Settings, Privacy, Location Services, GreenWay. On Android: Settings, Apps, GreenWay, Permissions, Location.

2. 2

   Make sure GPS is turned on, not just Wi-Fi location

   In some areas, Wi-Fi-based location is inaccurate. Turn on full GPS (high accuracy mode on Android) for a precise position fix at the station.

3. 3

   Step outside your vehicle briefly

   If GPS signal is weak (underground parking, dense urban area), step a few meters away from your car with your phone. This can help the GPS lock onto your position.

4. 4

   Try selecting the charger manually

   If the app cannot determine your location, try tapping on the station on the map manually or entering the charger's ID number (printed on the charger unit). Some app versions allow manual selection as a fallback.

Coverage gaps between cities

GreenWay's network is concentrated in and around cities. Between major cities, especially on secondary roads, there can be long stretches with no GreenWay stations.

Symptoms

• No GreenWay stations shown on the app map for 100+ km stretches
• The nearest GreenWay station requires a detour off your route
• You planned a trip assuming GreenWay coverage and ran into a gap
• Available stations between cities are AC-only (slow), not DC fast charging

How to Fix It

1. 1

   Plan your route and charging stops before leaving

   Use the GreenWay app or a route planner like ABRP (A Better Route Planner) to map out charging stops. Identify gaps in advance so you are not caught by surprise.

2. 2

   Have alternative charging networks ready

   Install apps for other networks that operate in the region. In Slovakia and Poland, look for Ionity, Shell Recharge, or Greencharge. In Czech Republic, check CEZ or PRE. Having multiple apps ensures you always have a fallback.

3. 3

   Charge to a higher level before entering a gap

   If you know there is a 150+ km stretch without fast chargers, charge to 90 or even 95% at the last available station. The slower charging speed above 80% is worth it if the alternative is running out of range.

4. 4

   Check for AC chargers as emergency backup

   Hotels, shopping centers, and some gas stations in Central Europe have AC chargers (Type 2, 11 to 22 kW). These are slow but can add enough range to reach the next fast charger. Many are accessible through Chargemap or Plugsurfing.

Charger screen errors in local language only

When a GreenWay charger displays an error, the message is often in Slovak, Polish, or Czech with no English translation. Understanding what went wrong is difficult.

Symptoms

• Error message appears in Slovak, Polish, or Czech
• You cannot tell if the error is temporary or requires support
• The charger stopped and you do not know why
• The error code is visible but the description is in a language you do not read

How to Fix It

1. 1

   Note the error code, not just the text

   Most error messages include a numeric or alphanumeric code (like E-101 or ERR_04). Write down or photograph the code. This is useful for support and often means the same thing regardless of language.

2. 2

   Use your phone camera to translate the screen

   Open Google Translate or Apple Translate, switch to camera mode, and point it at the charger screen. This gives a real-time translation of the error message.

3. 3

   Try unplugging and restarting the session

   Many error messages clear on a retry. Unplug, wait 15 seconds, plug back in, and start a new session through the app. Common errors like 'Communication timeout' resolve themselves.

4. 4

   Contact GreenWay support with the error code

   If the error persists, contact support through the GreenWay app. Provide the error code and the station ID (printed on the charger). GreenWay support can tell you whether the issue is temporary or requires a technician.

Power limited at older installations

Some older GreenWay stations deliver less than 150 kW. They may be rated at 50 kW or have degraded power output due to aging hardware.

Symptoms

• Charging speed maxes out at 50 kW on a station advertised as 150 kW
• The charger label says 150 kW but your vehicle never receives more than 50 kW
• Speed is significantly lower than what you get at newer GreenWay stations
• The app shows the station as 150 kW but the charger hardware looks older

How to Fix It

1. 1

   Check the charger label for the actual rated power

   The charger unit itself has a label showing its maximum output. Older GreenWay units may be rated at 50 kW despite the station listing showing 150 kW (which may refer to a newer unit at the same location).

2. 2

   Check if the station has multiple charger types

   Some GreenWay stations have both older 50 kW and newer 150 kW chargers. Make sure you are plugged into the newer, higher-power unit. It is usually the larger cabinet.

3. 3

   Verify your vehicle's battery level and temperature

   Your vehicle limits charging speed when the battery is above 60 to 80% or when the battery is cold. Check your dashboard to confirm the car is requesting more than what the charger delivers.

4. 4

   Use a different station if speed matters

   If you need faster charging and the station is limited, check the GreenWay app for a newer station nearby. Filter by power level to find 150 kW units specifically.