MG MG4 Charging at Atlante

MG MG4 Charger Won't Start? How to Fix It Now

You have plugged in your MG MG4 but nothing is happening. The charger light is blinking, the car is not responding, or you are getting an error message. This is frustrating, but most failed charging sessions have a simple fix. Let's walk through the common causes.

Symptoms

• Charger display shows an error code or red indicator
• CCS2 connector clicks in but charging does not begin
• Car dashboard shows no charging activity after plugging in
• Charger screen asks for authentication but does not accept your card or app
• Charging port light on the MG4 flashes or stays amber

What to Do

1. 1

   Check the charger screen for error messages

   Read any error codes or messages on the charger display. Common messages include 'authentication required,' 'connector error,' or 'out of service.' This tells you whether the problem is the charger or the car.

2. 2

   Unplug and replug the connector

   Remove the CCS2 or Type 2 connector completely, wait 10 seconds, and plug it back in firmly. Make sure you hear the click and the MG4's charge port light responds.

3. 3

   Authenticate again

   Re-tap your RFID card, restart the session in the app, or try contactless payment. Some chargers require you to authenticate before plugging in, others after. Try both sequences.

4. 4

   Disable scheduled charging

   On the MG4's infotainment screen, go to vehicle settings and check if scheduled charging is enabled. Turn it off temporarily to allow immediate charging.

5. 5

   Lock and unlock the car

   Use the MG4's key fob or the MG iSMART app to lock and then unlock the car. This can reset the charge port communication and clear temporary errors.

6. 6

   Try a different charger or stall

   If nothing works on this stall, try another one at the same station. If the entire station fails, the problem is likely the charger infrastructure, not your MG4.

MG MG4 Charging Payment Failed? Fix It Quickly

You are at a charger with your MG MG4 and the payment is not going through. Your card gets rejected, the app throws an error, or you cannot figure out how to pay at all. Payment issues are one of the most common reasons a charging session fails to start. Here is how to sort it out.

Symptoms

• RFID card tap does not register on the charger
• Charging app shows a payment error or insufficient funds
• Contactless bank card is declined at the charger terminal
• Charger asks for payment but you cannot find a method that works
• Session starts but stops immediately due to payment authorization failure

What to Do

1. 1

   Check which payment methods the charger accepts

   Look at the charger for logos showing accepted payment types: RFID, app, contactless card, QR code. Many chargers display the logos of compatible networks near the screen or card reader.

2. 2

   Try the network's app

   Scan the QR code on the charger or search for the network's app in your phone's app store. Many networks let you start a session through their app even without an RFID card.

3. 3

   Try a different payment method

   If your RFID card fails, try the app. If the app fails, try contactless. If you have a multi-network roaming card (like Plugsurfing or Shell Recharge), try that instead.

4. 4

   Check your card balance and bank notifications

   Open your banking app to check for declined transactions or pre-authorization holds. Contact your bank if the charger is trying to authorize a large hold that exceeds your available balance.

5. 5

   Use a roaming service

   If you do not have an account with this specific network, a roaming provider like Plugsurfing, Chargemap, or Shell Recharge may cover this charger. These services work across multiple networks with one card or app.

6. 6

   Find an alternative charger nearby

   If payment truly will not work, search for another charger nearby. Filter your charging app by your available payment methods to find a compatible station.

MG MG4 Charging Slowly? Causes and Quick Fixes

You plugged in your MG MG4 expecting fast charging, but the kW reading is disappointingly low. This is one of the most common frustrations for MG4 drivers, and it usually has a straightforward explanation. Here is what to check and how to get closer to the 142kW DC maximum your car supports.

Symptoms

• DC charging power showing well below 142kW on the charger display
• AC home or destination charging stuck below 11kW
• Estimated charging time much longer than expected
• Battery percentage climbing very slowly after 60-70% SOC
• Charging power drops significantly in cold weather

What to Do

1. 1

   Check the charger's rated power

   Look at the charger label or app to confirm its maximum output. If it is a 50kW unit, your MG4 cannot charge faster regardless of its 142kW capability.

2. 2

   Check your battery temperature and SOC

   On the MG4's instrument cluster, check your current state of charge. If you are above 70%, the taper is normal. In cold weather, use the preconditioning feature by setting the charger as your navigation destination.

3. 3

   Activate preconditioning via navigation

   Set the fast charger as your destination in the MG4's built-in navigation. This triggers battery preconditioning, warming the pack to an optimal temperature before you arrive.

4. 4

   Try a different CCS2 stall

   If the charger has multiple stalls, power may be shared between them. Try an adjacent stall or wait for other cars to finish. Some charging sites have dedicated high-power stalls.

5. 5

   Check your AC charging cable

   For AC charging, make sure you are using a cable rated for at least 11kW (3-phase, 16A). A single-phase cable limits you to about 3.6kW regardless of what the charger or car supports.

6. 6

   Verify no charging limit is set in the car

   In the MG4's settings, check if a charging current limit or maximum SOC limit has been set. A reduced AC charging current setting will cap your speed even on a capable charger.

New station with teething problems

Atlante is expanding rapidly, and many stations are brand new. Newly installed chargers sometimes have firmware bugs, incomplete network configuration, or hardware that has not been fully tested under real-world conditions.

Symptoms

• Charger turns on but fails to communicate with your vehicle
• Session starts but drops after a few seconds
• Charger screen shows an error code you have never seen before
• Station appears on the map but the chargers are not yet operational

How to Fix It

1. 1

   Try a different charger at the same station

   New stations often have multiple units and the issue may be limited to one charger. Try another unit before giving up on the location.

2. 2

   Unplug, wait 30 seconds, and retry

   New charger firmware sometimes fails on the first handshake but succeeds on the second attempt. A short wait lets the charger reset its session state.

3. 3

   Start the session through the Atlante app

   If the charger's screen or contactless reader is not working properly, the app provides a separate communication path to the charger's backend. This can bypass local hardware issues.

4. 4

   Check the Atlante app for station status notes

   Atlante sometimes posts notices about newly activated stations that are still in testing. The station detail page in the app may show a note about limited functionality.

5. 5

   Report the issue and move to the next station

   Use the Atlante app to report the problem. New station issues are usually fixed quickly once reported. Check the app for the nearest alternative Atlante or competitor station.

App crashes on older phones

The Atlante app can be unstable on older phones or phones running outdated operating systems. The app may crash during login, while loading the map, or in the middle of starting a session.

Symptoms

• App closes unexpectedly when you open the station map
• App freezes during the payment screen
• Login screen loads but the app crashes after entering credentials
• App works briefly but crashes when you try to start a session

How to Fix It

1. 1

   Update the Atlante app to the latest version

   Atlante pushes frequent updates that fix stability issues. Open the App Store or Google Play and check for updates before your trip.

2. 2

   Clear the app cache

   On Android, go to Settings, Apps, Atlante, and clear the cache. On iPhone, delete and reinstall the app. Corrupted cache data is a common cause of crashes.

3. 3

   Check your phone's operating system version

   The Atlante app may require iOS 15+ or Android 10+. If your phone is on an older version, update if possible. If your phone cannot update, you may need a roaming app as a backup.

4. 4

   Use contactless payment as a fallback

   If the app keeps crashing and the station supports contactless, tap your credit or debit card on the charger's payment terminal. Not all Atlante stations have this yet, but it completely bypasses the app.

5. 5

   Try a roaming app

   Apps like Chargemap, Shell Recharge, or Electropass can start sessions at Atlante stations without using the Atlante app. Check roaming coverage before relying on this.

Contactless payment terminal not activated

Atlante is rolling out contactless card payment across its network, but not every charger has an active terminal yet. Some units have the hardware installed but the payment function is not turned on.

Symptoms

• Card reader is visible on the charger but does not respond to a tap
• Screen says 'Use app to start' with no contactless option shown
• Contactless symbol is printed on the charger but the reader light is off
• You see a payment terminal but tapping produces no response

How to Fix It

1. 1

   Download and use the Atlante app

   At stations where contactless is not yet active, the Atlante app is the primary payment method. Download it before your trip and add a payment card in advance.

2. 2

   Check the charger screen for payment instructions

   Some Atlante chargers display which payment methods are currently available. If contactless is not listed, the terminal is not active at that unit.

3. 3

   Try a different charger at the same station

   Contactless activation sometimes rolls out unit by unit. Another charger at the same station may have an active terminal.

4. 4

   Use a roaming RFID card or app

   If you have an RFID card from a roaming provider, try tapping it. Some Atlante stations accept roaming RFID even when the contactless card terminal is not active.

Charger screen hard to read in direct sunlight

Some Atlante charger screens have low brightness levels that make them nearly impossible to read in bright sunlight. This is especially common at stations in Southern Europe during summer.

Symptoms

• Screen content is barely visible outdoors during the day
• You cannot read the price, status, or error messages on the screen
• Screen appears to be off but the charger is actually on
• You have to cup your hands around the screen to read it

How to Fix It

1. 1

   Use your body or hand to shade the screen

   Stand to block direct sunlight from hitting the screen. Even partial shade can make the display readable.

2. 2

   Take a photo of the screen with your phone

   Your phone camera can sometimes capture what your eyes cannot. Take a photo and zoom in to read the text.

3. 3

   Use the Atlante app to monitor your session

   All session information (charging speed, energy delivered, cost, estimated time) is available in the app. You do not need the charger screen to track your session.

4. 4

   Start the session entirely through the app

   If you cannot read the screen at all, use the Atlante app to select the charger, start the session, and stop it when done. This avoids needing to interact with the screen.

Cable connector requires specific angle to lock

Some Atlante charger cables need to be inserted at a particular angle or with extra force for the CCS2 connector to seat properly. If it is not fully locked, the session will not start.

Symptoms

• Connector feels like it is in but the charger does not recognize it
• Charger screen says 'Connect cable' even though the cable is plugged in
• You hear a partial click but the connector is not locked
• Connector slides back out after you let go

How to Fix It

1. 1

   Push the connector straight in, then slightly upward

   Some Atlante CCS2 connectors need a slight upward tilt after the initial push to engage the locking mechanism. You should feel and hear a solid click.

2. 2

   Check for debris in the vehicle's charging port

   Dust, ice, or a small pebble in the port can prevent the connector from seating fully. Inspect the port and brush out anything you find.

3. 3

   Make sure the vehicle is unlocked and ready to charge

   Some vehicles lock the charging port flap or disable the inlet when the car is locked or in drive mode. Ensure the car is in park and unlocked.

4. 4

   Try a different cable if the charger has two

   If the charger has two CCS2 cables, try the other one. One cable may have a slightly worn connector that does not seat as easily.