Mercedes eVito Charging at GreenWay

Mercedes eVito Van Charger Will Not Start a Session

You have connected the charger to your Mercedes eVito and nothing is happening. No session, no power, no charging light. When you are between jobs or trying to charge at the depot, you need this resolved quickly. Here is how.

Symptoms

• CCS2 or Type 2 connector is plugged in but no session starts
• The MBUX display does not show charging activity
• The charger screen shows an error after plug-in
• The charge port indicator stays off or flashes amber
• The depot wallbox status light does not change when plugged in

What to Do

1. 1

   Authenticate before plugging in

   At public chargers, tap your RFID card or start the session in the app before inserting the connector. Wait for the charger to confirm it is ready.

2. 2

   Clean and reinsert the connector

   Remove the connector, wipe the charge port on the eVito with a dry cloth to remove any dirt, then reinsert the connector firmly until it clicks.

3. 3

   Check MBUX charging settings

   On the MBUX display, navigate to the charging menu. Check if departure time charging is active. Disable it for immediate charging.

4. 4

   Check the depot electrical panel

   If at the depot, check the circuit breaker for the charging circuit. Also check the wallbox status indicator. Report issues to your fleet manager.

5. 5

   Lock and unlock the van

   Use the key to lock the eVito, wait 20 seconds, then unlock. This can reset the charging electronics after a fault state.

6. 6

   Move to a different charger

   If the charger is faulty, do not waste time. Move to another unit or station, especially if you are mid-route.

Mercedes eVito Van Payment Failed at Charging Station

You are at a public charger with your Mercedes eVito and the payment will not go through. Whether it is a fleet card, personal RFID, or an app, payment failures at public chargers waste time between jobs. Here is how to resolve it fast.

Symptoms

• Fleet card does not start a session at the charger
• RFID card tap produces no response
• Charging app shows a payment authorization error
• Contactless bank card is declined
• Charger shows 'payment failed' on the screen

What to Do

1. 1

   Check accepted payment methods

   Look at the charger stickers and screen for accepted networks and cards. If your fleet card logo is not shown, this charger is not on your network.

2. 2

   Try a different payment method

   Switch between fleet card, personal RFID, charging app, and contactless bank card. One may work where others fail.

3. 3

   Verify fleet card status

   Contact your fleet manager or check the fleet card provider app to confirm the card is active and has not hit a spending limit.

4. 4

   Hold the card steadily

   Place the card flat against the reader for 3 seconds. Do not tap and pull away quickly. Gloves can interfere with NFC reading.

5. 5

   Cancel and retry

   Cancel any pending session in the app, wait 60 seconds, and start a fresh attempt.

6. 6

   Move to another charger unit

   If the payment reader on this unit is broken, try the next charger at the station. Do not waste time troubleshooting hardware you cannot fix.

Mercedes eVito Van Charging Slower Than Expected Speed

Your Mercedes eVito is charging slower than the 110 kW DC maximum. Or your depot wallbox is barely delivering power overnight. Without battery preconditioning, the eVito is especially sensitive to cold weather. Here is what to check and how to improve your charging speed.

Symptoms

• DC fast charging well below the 110 kW maximum
• Depot AC charging stuck at 3-4 kW instead of 11 kW
• Charging speed drops quickly after 40-50% state of charge
• Winter charging starts extremely slowly
• Mid-route DC charging takes too long between jobs

What to Do

1. 1

   Drive before charging in cold weather

   Since the eVito lacks preconditioning, drive for at least 20-30 minutes before stopping at a DC charger in winter. This warms the battery through use.

2. 2

   Charge between 20-50% for fastest speeds

   Plan your mid-route charging stops to arrive between 20-50% state of charge. This is where the eVito can approach its 110 kW peak.

3. 3

   Check your depot charger wiring

   Ask your fleet manager or electrician to verify the depot wallbox is wired for three-phase at 16A per phase for 11 kW. Single-phase installations are common but much slower.

4. 4

   Choose unshared DC chargers

   At public stations, check if the charger is sharing power. If another vehicle is on the paired connector, try a different unit.

5. 5

   Use MBUX to check charging status

   The MBUX infotainment system shows current charging power and estimated time. Use this to verify speeds and decide if you should move to a different charger.

6. 6

   Try a different charger

   If speeds remain well below expected at a low state of charge, the charger may be faulty. Move to another unit.

App-only payment with no backup option

GreenWay stations require the GreenWay app to start a session. There are no contactless card readers or RFID pads. If the app fails or your phone dies, you cannot charge.

Symptoms

• No card reader or RFID pad visible on the charger
• Charger screen shows a QR code or 'Use app to start' message
• You arrived without the app installed and cannot begin a session
• Your phone battery is low and you are worried it will die during setup

How to Fix It

1. 1

   Download the GreenWay app before your trip

   This is non-negotiable for GreenWay stations. Install the app, create an account, and add a payment method while you have good internet and battery. Do this before you leave, not at the charger.

2. 2

   Charge your phone before arriving at the station

   Since you need your phone to start and monitor the session, make sure it has enough battery. Use your car's USB port or a power bank on the way.

3. 3

   Try a roaming app as a backup

   Some GreenWay stations are accessible through roaming providers like Plugsurfing, Shell Recharge, or Chargemap. Check your roaming app's map to see if the specific station is covered before counting on it.

4. 4

   Scan the QR code on the charger

   If you do not have the app, scan the QR code with your phone camera. It may direct you to the app store or, in some cases, to a web-based session start page.

App requires location services for charger activation

The GreenWay app needs location services turned on to activate a charger. Without it, the app cannot verify that you are at the station and will not let you start a session.

Symptoms

• App shows 'Enable location services' and will not proceed
• You can see the charger on the map but cannot start a session
• The 'Start charging' button is grayed out or unresponsive
• App shows your location incorrectly, placing you far from the station

How to Fix It

1. 1

   Enable location services for the GreenWay app

   Go to your phone settings, find the GreenWay app, and set location access to 'While Using' or 'Always.' On iPhone: Settings, Privacy, Location Services, GreenWay. On Android: Settings, Apps, GreenWay, Permissions, Location.

2. 2

   Make sure GPS is turned on, not just Wi-Fi location

   In some areas, Wi-Fi-based location is inaccurate. Turn on full GPS (high accuracy mode on Android) for a precise position fix at the station.

3. 3

   Step outside your vehicle briefly

   If GPS signal is weak (underground parking, dense urban area), step a few meters away from your car with your phone. This can help the GPS lock onto your position.

4. 4

   Try selecting the charger manually

   If the app cannot determine your location, try tapping on the station on the map manually or entering the charger's ID number (printed on the charger unit). Some app versions allow manual selection as a fallback.

Coverage gaps between cities

GreenWay's network is concentrated in and around cities. Between major cities, especially on secondary roads, there can be long stretches with no GreenWay stations.

Symptoms

• No GreenWay stations shown on the app map for 100+ km stretches
• The nearest GreenWay station requires a detour off your route
• You planned a trip assuming GreenWay coverage and ran into a gap
• Available stations between cities are AC-only (slow), not DC fast charging

How to Fix It

1. 1

   Plan your route and charging stops before leaving

   Use the GreenWay app or a route planner like ABRP (A Better Route Planner) to map out charging stops. Identify gaps in advance so you are not caught by surprise.

2. 2

   Have alternative charging networks ready

   Install apps for other networks that operate in the region. In Slovakia and Poland, look for Ionity, Shell Recharge, or Greencharge. In Czech Republic, check CEZ or PRE. Having multiple apps ensures you always have a fallback.

3. 3

   Charge to a higher level before entering a gap

   If you know there is a 150+ km stretch without fast chargers, charge to 90 or even 95% at the last available station. The slower charging speed above 80% is worth it if the alternative is running out of range.

4. 4

   Check for AC chargers as emergency backup

   Hotels, shopping centers, and some gas stations in Central Europe have AC chargers (Type 2, 11 to 22 kW). These are slow but can add enough range to reach the next fast charger. Many are accessible through Chargemap or Plugsurfing.

Charger screen errors in local language only

When a GreenWay charger displays an error, the message is often in Slovak, Polish, or Czech with no English translation. Understanding what went wrong is difficult.

Symptoms

• Error message appears in Slovak, Polish, or Czech
• You cannot tell if the error is temporary or requires support
• The charger stopped and you do not know why
• The error code is visible but the description is in a language you do not read

How to Fix It

1. 1

   Note the error code, not just the text

   Most error messages include a numeric or alphanumeric code (like E-101 or ERR_04). Write down or photograph the code. This is useful for support and often means the same thing regardless of language.

2. 2

   Use your phone camera to translate the screen

   Open Google Translate or Apple Translate, switch to camera mode, and point it at the charger screen. This gives a real-time translation of the error message.

3. 3

   Try unplugging and restarting the session

   Many error messages clear on a retry. Unplug, wait 15 seconds, plug back in, and start a new session through the app. Common errors like 'Communication timeout' resolve themselves.

4. 4

   Contact GreenWay support with the error code

   If the error persists, contact support through the GreenWay app. Provide the error code and the station ID (printed on the charger). GreenWay support can tell you whether the issue is temporary or requires a technician.

Power limited at older installations

Some older GreenWay stations deliver less than 150 kW. They may be rated at 50 kW or have degraded power output due to aging hardware.

Symptoms

• Charging speed maxes out at 50 kW on a station advertised as 150 kW
• The charger label says 150 kW but your vehicle never receives more than 50 kW
• Speed is significantly lower than what you get at newer GreenWay stations
• The app shows the station as 150 kW but the charger hardware looks older

How to Fix It

1. 1

   Check the charger label for the actual rated power

   The charger unit itself has a label showing its maximum output. Older GreenWay units may be rated at 50 kW despite the station listing showing 150 kW (which may refer to a newer unit at the same location).

2. 2

   Check if the station has multiple charger types

   Some GreenWay stations have both older 50 kW and newer 150 kW chargers. Make sure you are plugged into the newer, higher-power unit. It is usually the larger cabinet.

3. 3

   Verify your vehicle's battery level and temperature

   Your vehicle limits charging speed when the battery is above 60 to 80% or when the battery is cold. Check your dashboard to confirm the car is requesting more than what the charger delivers.

4. 4

   Use a different station if speed matters

   If you need faster charging and the station is limited, check the GreenWay app for a newer station nearby. Filter by power level to find 150 kW units specifically.