Mercedes-Benz EQS Charging at Allego

Mercedes-Benz EQS Charger Won't Start a Session

You connected the CCS2 cable to your EQS's right rear charge port, but the Hyperscreen shows no charging activity. No power flowing, no progress. This is frustrating, especially in a flagship sedan where everything should just work. The cause is usually authentication, cable seating, or the charger itself, not the EQS.

Symptoms

• CCS2 connector plugged in but the Hyperscreen shows no charging activity
• Charger screen displays an error or stays idle after authentication attempt
• Plug & Charge does not authenticate automatically at a supported station
• Charge port LED does not illuminate or blinks an error pattern
• Mercedes me app shows the EQS as connected but not charging

What to Do

1. 1

   Remove and firmly reseat the CCS2 connector

   Pull the connector out of the right rear charge port. Check for debris or moisture. Push it back in straight and firm until you hear a click and see the charge port LED respond. The CCS2 connector is heavy, so support it with both hands to ensure proper alignment.

2. 2

   Authenticate manually if Plug & Charge failed

   Open the charging network's app and start the session by scanning the QR code or selecting the charger. If you have an RFID card for this network, tap it on the reader. Do not wait for Plug & Charge if it did not work within 30 seconds.

3. 3

   Disable scheduled charging in MBUX

   On the Hyperscreen, open Settings, then Charging. Turn off any departure time or scheduled charging window. At a public charger, you want charging to start immediately. Re-enable scheduled charging when you are back at your home wallbox.

4. 4

   Lock and unlock the EQS to reset the charge controller

   Use the key or Mercedes me app to lock the car. Wait 15 seconds, then unlock. This resets the charge port locking mechanism and the onboard charging communication module. Reconnect the cable after unlocking.

5. 5

   Try a different connector or charger at the station

   If the station has multiple CCS2 connectors, try a different one. If the entire station seems unresponsive, use MBUX navigation to find another nearby charger. Report the faulty charger through the network's app.

Mercedes-Benz EQS Payment Failed at Charging Station

You are standing next to your EQS at a public charger and payment will not go through. Plug & Charge did not activate, the app shows an error, or your card was declined. Payment failures are one of the most common reasons charging sessions do not start. With the EQS, you have multiple authentication options to try before giving up.

Symptoms

• Plug & Charge does not authenticate when the CCS2 cable is connected
• Contactless card declined at the charger's payment terminal
• Mercedes me Charge or the network's app shows a payment error
• RFID card not recognized by the charger reader
• Session starts but stops immediately with a billing-related error

What to Do

1. 1

   Try Plug & Charge by connecting the cable

   Plug the CCS2 connector into the EQS's right rear charge port. Wait up to 30 seconds for Plug & Charge to authenticate. Check the Hyperscreen for a charging confirmation. If nothing happens after 30 seconds, Plug & Charge is not working at this station.

2. 2

   Use the charging network's app to start the session

   Open the app for the charging network shown on the charger. Scan the QR code or enter the charger ID. Start the session through the app. Verify your payment method in the app is valid and not expired.

3. 3

   Try contactless payment at the charger terminal

   If the charger has a contactless payment terminal, tap your bank card, Apple Pay, or Google Pay. If the first card is declined, try a different one. Some terminals accept only certain card brands.

4. 4

   Verify your Mercedes me Charge account

   Open the Mercedes me app. Go to Charge settings and check that Plug & Charge is enabled and your payment method is current. If you recently changed your payment method, it may need time to sync. Try restarting the Mercedes me app.

5. 5

   Try a different RFID card or roaming provider

   If you carry multiple RFID cards, try another network. Roaming providers with broad European coverage (Chargemap, Maingau, Shell Recharge) can fill gaps where Mercedes me Charge does not reach.

6. 6

   Find an alternative charger nearby

   If payment fails on this charger entirely, use the Hyperscreen to find another station nearby. A different charging network may accept your payment method. Filter by the networks you know work with your cards.

Mercedes-Benz EQS Charging Slower Than Expected

You plugged in your EQS at a 300 kW charger expecting close to 200 kW, but the Hyperscreen shows 50 kW. Or your home wallbox is stuck at 3.6 kW instead of 11 kW (or 22 kW if you have the optional upgrade). The EQS has a huge 118 kWh battery that can take a while to warm up. Slow charging is almost always temperature, state of charge, or the charger, not a defect.

Symptoms

• DC fast charging speed well below the 200 kW maximum shown on the Hyperscreen
• AC charging stuck at 3-4 kW instead of 11 kW or 22 kW
• Charging speed drops sharply after reaching 50-60% state of charge
• Charging session starts at reasonable speed but slows within minutes
• The 118 kWh battery takes significantly longer to charge than expected

What to Do

1. 1

   Route to the charger using MBUX navigation

   Enter the charging station as your destination on the Hyperscreen or MBUX. This activates automatic battery preconditioning for the 118 kWh pack. The EQS will display a preconditioning notification. Given the large battery, start routing at least 20-30 minutes before arrival for maximum benefit in cold weather.

2. 2

   Check your state of charge before expecting peak speed

   The EQS reaches 200 kW only at lower state of charge levels. For the fastest DC charging, arrive between 10-20%. If you are above 60%, the speed reduction is normal. With 580 km of range, you often do not need to charge above 80% on road trips.

3. 3

   Verify the charger can deliver the speed you expect

   Check the charger's rated output on the unit itself or in the charging app. A 50 kW charger will never give your EQS more than 50 kW. Look for chargers rated 150 kW or higher to take advantage of the EQS's capabilities. Avoid stalls paired with another vehicle.

4. 4

   Check AC charging settings and wallbox compatibility

   Open the charging settings in MBUX. Confirm the charge current is set to maximum. If you have the optional 22 kW onboard charger, verify your wallbox is 3-phase 32A. For the standard 11 kW charger, you need at least 3-phase 16A.

5. 5

   Check if Plug & Charge negotiated the correct power

   The EQS supports Plug & Charge. Occasionally, authentication issues cause the charger to default to a lower power tier. Unplug from the right rear charge port, wait 30 seconds, and reconnect. Check MBUX for any authentication errors.

6. 6

   Try a different charger

   If the speed is still low after checking all settings, try a different charger. Some chargers degrade over time. Use MBUX navigation or the Mercedes me app to find a high-power charger (150 kW+) nearby.

Allego app not starting a session

You open the Allego app, select the charger, tap 'Start,' and nothing happens. The app may spin, show an error, or claim the charger is offline even though the screen in front of you says otherwise.

Symptoms

• Allego app shows a loading spinner that never finishes
• 'Charger unavailable' in the app but the physical charger looks operational
• App crashes when tapping 'Start Charging'
• Session appears to start in the app but the charger does not begin delivering power

How to Fix It

1. 1

   Make sure you selected the correct charger and connector

   Allego stations often have multiple charging points. Each one has its own ID, usually printed on a sticker near the connector. Match this ID to the one shown in the Allego app. Selecting the wrong point is the most common reason a session will not start.

2. 2

   Plug in the cable before starting the session in the app

   Most Allego chargers require the cable to be connected to your car first. The charger needs to detect a vehicle before it will accept a start command from the app.

3. 3

   Close and reopen the Allego app

   Force-close the app completely (swipe it away from your recent apps), wait a few seconds, and reopen it. Try starting the session again.

4. 4

   Scan the QR code on the charger instead

   Most Allego chargers have a QR code that opens a web-based payment page. This works independently of the Allego app and lets you pay with a credit card without needing an account.

5. 5

   Use an RFID card from a roaming provider

   If you have an RFID card from a provider like Shell Recharge, Plugsurfing, or Chargemap, hold it against the reader on the charger. This bypasses the Allego app entirely.

Charger not appearing in the Allego app

You are standing in front of a physical Allego charger, but it does not show up on the Allego app map. The charger is clearly operational and other drivers are using it.

Symptoms

• Charger location is missing from the the Allego app map entirely
• App shows the location but with zero available connectors
• Charger appears under a different brand name in other apps but not in the Allego app
• Newly installed charger not yet listed

How to Fix It

1. 1

   Check if the charger is operated under a different brand

   Allego operates under various local labels in different countries. The charger might be listed under the local brand name rather than 'Allego' in some apps. Look for a sticker or sign on the charger that shows the operator name and EVSE ID.

2. 2

   Search by charger ID instead of location

   In the Allego app, try the search function and enter the charger's EVSE ID (printed on the unit, usually starting with a country code like DE*, NL*, or FR*). This can find chargers that are not correctly placed on the map.

3. 3

   Use the QR code on the charger

   Scan the QR code on the charger with your phone camera. This will open a direct link to start a session, even if the charger is missing from the app map.

4. 4

   Try a different charging app

   Allego chargers are accessible through many roaming providers. Open an app like Chargemap, Shell Recharge, or Plugsurfing and search for the same location. You may be able to start the session there.

Third-party RFID card not accepted

You hold your RFID card from another provider against the reader and the charger beeps but rejects it, or nothing happens at all.

Symptoms

• Charger beeps once but displays 'Card not recognized'
• No reaction when holding the RFID card to the reader
• Card works at other networks but not at this Allego charger
• 'Authorization failed' message on the charger screen

How to Fix It

1. 1

   Check if your roaming provider covers Allego

   Not all RFID providers have roaming agreements with Allego. Check your provider's app or website to confirm Allego is listed in their coverage. Some providers cover only certain Allego locations.

2. 2

   Hold the card flat and steady for 3 seconds

   Do not wave or tap the card. Place it flat against the reader and hold it still. Allego readers can be slower to respond than some other networks.

3. 3

   Try a different position on the reader

   The RFID antenna inside the reader has a specific sweet spot. Move your card slowly across the reader surface until you get a response. On some Allego chargers, the reader is on the right side panel rather than the front.

4. 4

   Check your RFID card is activated

   Some providers require you to activate your RFID card in their app before first use. Open your provider's app and look for card activation or card management settings.

5. 5

   Fall back to QR code or Allego app

   If your RFID card will not work, scan the QR code on the charger for direct credit card payment, or download the Allego app and register to start the session digitally.

Long delay before charging actually starts

You have authenticated and the charger says it is starting, but 30 seconds, sometimes over a minute, passes before any power flows to your car.

Symptoms

• Charger screen says 'Starting' or 'Initializing' for over 30 seconds
• Car shows 'Waiting for charger' or 'Preparing'
• Power reading stays at 0 kW for a full minute after authentication
• You wonder if you should unplug and try again

How to Fix It

1. 1

   Wait at least 90 seconds before taking action

   Allego high-power chargers perform a communication handshake with your car before delivering power. This includes safety checks, voltage negotiation, and isolation testing. A 30-60 second delay is normal, especially on 350 kW units.

2. 2

   Do not unplug during the initialization phase

   Unplugging and re-plugging resets the entire handshake process. If the charger screen shows any progress (status messages, icons changing), let it complete.

3. 3

   Check if your car's charge port is locked

   The connector should be locked into your car's charge port during initialization. If you can wiggle the connector freely, it may not be fully inserted. Push it in firmly and listen for the lock click.

4. 4

   If nothing happens after 2 minutes, restart the session

   Unplug the connector, wait 10 seconds, plug it back in, and authenticate again. If the delay repeats, try a different connector or charger at the same station.

Charging power much lower than advertised

The charger is rated for 350 kW, but your car is only pulling 50 kW or less. The session is working, just far slower than expected.

Symptoms

• Car or charger display shows 40-80 kW on a 350 kW charger
• Estimated charge time is much longer than expected
• Power started high but dropped dramatically within minutes
• Other cars at the same station seem to charge faster

How to Fix It

1. 1

   Check your battery level

   DC charging slows significantly above 60-70% state of charge on most cars. If your battery is already at 65% or higher, the reduced speed is your car protecting its battery, not a charger problem.

2. 2

   Check your car's maximum DC charging rate

   A 350 kW charger can deliver up to 350 kW, but your car decides how much to accept. Many EVs top out at 100-150 kW. Check your car's specifications for its maximum DC charging speed.

3. 3

   Consider battery temperature

   Cold batteries charge slowly. If you have been parked for hours in cold weather without preconditioning, your car may limit charging to 30-60 kW until the battery warms up. Some cars let you precondition the battery by setting the charger as your navigation destination.

4. 4

   Check if the station is power-sharing

   Some Allego stations share power between multiple chargers. If three cars are charging simultaneously, each one may get less than the maximum. This is normal at shared-power sites.

5. 5

   Try a different connector at the same station

   Occasionally one connector delivers less power due to a hardware limitation. If you are getting unusually low power even at a low battery level, unplug and try the next unit.