Kia EV9 Charging at EnBW mobility+

Kia EV9 Charger Won't Start? Step-by-Step Fix Guide

You have plugged the cable into your EV9's right rear charge port, but nothing is happening. No charging indicator on the panoramic display, no LED confirmation. On a large SUV you rely on for family trips or long drives, a failed charge start can be stressful. In most cases, the issue is authentication, utility mode being on, a car setting, or the charger itself.

Symptoms

• CCS2 or Type 2 cable plugged in but no charging indicator on the panoramic display
• Charge port LED stays off or flashes red
• Charger screen shows an error or remains on the start screen
• Kia Connect app shows the car is not connected to a charger
• Charging starts briefly then stops within a few seconds

What to Do

1. 1

   Turn off V2L utility mode

   On the EV9's infotainment screen, go to EV settings. Make sure utility mode or V2L is turned off. Also check the exterior V2L outlet on the rear bumper. If a device was plugged in there, the car may still be in discharge mode.

2. 2

   Check the charge port and cable

   Open the charge port on the right rear fender. The EV9 is a tall vehicle, so the port is relatively high. Press the flap firmly to open. Insert the CCS2 connector straight in until it clicks. The LED should light up.

3. 3

   Authenticate with the charger

   If Plug & Charge does not start the session, tap your RFID card, use the charging network's app, or try contactless payment. Have a backup method ready.

4. 4

   Check for a charging schedule

   On the infotainment screen, go to EV settings, then Scheduled Charging. If a schedule is active, disable it or tap 'Charge Now' to override. The Kia Connect app can also manage schedules.

5. 5

   Unplug, wait 30 seconds, and try again

   Remove the cable completely, wait 30 seconds, reconnect, and re-authenticate. This resets the communication between the EV9 and the charger.

6. 6

   Try a different charger

   If nothing works, try another stall at the same station or a different station. Report the broken charger through the charging network's app.

Kia EV9 Charger Payment Failed at a Public Station

You are at a public charger with your EV9, the CCS2 cable is connected, but the payment will not go through. The charger shows an error, the app is not cooperating, or your RFID card gets nothing. Payment problems are one of the most common reasons charging fails to start, and they are almost never a car problem. Here is how to work through it.

Symptoms

• Charger screen shows 'payment failed' or 'authorization error'
• RFID card tapped but the charger does not respond
• Charging network app shows an error during authorization
• Plug & Charge does not start the session automatically
• Contactless card payment declined at the terminal

What to Do

1. 1

   Try a different payment method

   If RFID failed, try the charging network's app. If the app failed, try contactless payment with a card. Switch between methods quickly rather than retrying the same one.

2. 2

   Check your charging network account

   Open the charging app and check your payment details. Look for expired cards, low prepaid balances, or account issues. Update your payment method if needed.

3. 3

   Verify Plug & Charge configuration

   In the Kia Connect app, check that Plug & Charge is enabled and linked to the correct charging network. Also verify that this specific station supports Plug & Charge. Not all stations do.

4. 4

   Look for a QR code on the charger

   Many chargers have a QR code that opens a web payment page. This lets you pay without an account or app. Scan it with your phone camera.

5. 5

   Try a different charger at the same station

   If one stall's payment terminal is not working, another may be fine. Walk to the next charger and try your payment method again.

Kia EV9 Charging Slower Than Expected at DC or AC

The EV9 is Kia's largest electric SUV, with a 96 kWh battery and 800V architecture that supports up to 233 kW DC charging. When you see 60 kW on the charger screen instead of 200+, it does not match what the specs promise. In most cases, slow charging on the EV9 comes down to battery temperature, the charger's actual voltage and output, or a car setting worth checking.

Symptoms

• DC fast charging speed well below the 233 kW maximum
• AC charging stuck at 3-4 kW instead of the full 11 kW
• Charging speed drops sharply above 60-70% state of charge
• Session starts at low power and never ramps up
• Panoramic display shows much lower power than the charger's rated output

What to Do

1. 1

   Check the battery temperature

   Look at the EV information on the panoramic display. If the battery is cold, use the built-in navigation to set a charging destination. The EV9 will precondition the battery automatically on the way. This is especially important in winter given the large battery.

2. 2

   Check whether the charger supports 800V

   Look at the charger specs on its screen or in the charging network's app. If it is a 400V charger, the EV9's multi-charging system handles the conversion, but you will not see 233 kW. Seek out chargers that explicitly list 800V support.

3. 3

   Check your state of charge

   If you are above 80%, the speed drop is normal. For road trips, plan stops to arrive between 10-20% and unplug at 80%. The EV9's consumption is around 204 Wh/km, so factor that into your stop planning.

4. 4

   Review scheduled charging and charge limits

   On the EV settings screen or in the Kia Connect app, check that scheduled charging is not delaying the session and the charge current limit is at maximum.

5. 5

   Check if the charger is sharing power

   Look at the charger cabinet. If two cables come from the same unit and someone is on the other cable, your speed may be halved. Move to an unoccupied charger if one is available.

6. 6

   Try a different charger or station

   If speed is still low after checking everything, the charger may be underperforming its rated output. Try another stall or head to a different station.

Roaming pricing unclear or higher than expected

You started a session through EnBW mobility+ and the per-kWh price was significantly higher than you expected. The same charger costs different amounts at different times, and the pricing logic feels opaque.

Symptoms

• Per-kWh rate on the receipt is higher than the rate shown on the EnBW website
• Same charger location costs more through EnBW mobility+ than through the CPO's own app
• Price differs between two chargers at the same station
• Unexpected 'roaming fee' or 'session fee' on your invoice

How to Fix It

1. 1

   Check the price before you start the session

   In the EnBW mobility+ app, tap on the charger and look for the pricing details before starting. The app shows the per-kWh rate for that specific charger. Prices vary because each CPO sets different roaming rates.

2. 2

   Understand the pricing tiers

   EnBW mobility+ groups chargers into pricing tiers. 'EnBW own' chargers are cheapest, 'roaming standard' is mid-range, and 'roaming plus' (typically high-power chargers from premium CPOs like Ionity) costs more. The tier is usually shown in the charger details.

3. 3

   Compare with the CPO's own app

   If a charger is operated by Ionity, for example, check the Ionity app or website for their direct pricing. Sometimes the CPO's own app or RFID card is cheaper because there is no roaming middleman. If you use that CPO frequently, their own account may save you money.

4. 4

   Consider the EnBW mobility+ tariff you are on

   EnBW offers different tariffs (with and without a monthly fee). The tariff with a monthly fee usually gives lower per-kWh rates. In the app, go to your profile to check which tariff you are on and whether switching would save you money based on your usage.

5. 5

   Watch for idle fees and blocking fees

   Some chargers accessed through EnBW mobility+ charge a per-minute fee after your car finishes charging but the cable is still plugged in. Move your car promptly once charging is complete to avoid these fees.

App not loading charger details

You tap on a charger pin on the map and the detail screen is blank, shows a loading spinner forever, or displays outdated information. You cannot see pricing, availability, or the start button.

Symptoms

• Charger detail page shows a permanent loading spinner
• Availability status not updating (shows 'Available' for hours at a busy station)
• Price information missing from the detail screen
• App shows 'No connection' error when loading charger details

How to Fix It

1. 1

   Check your phone's internet connection

   Charging stations are often in areas with poor cellular coverage, like parking garages, highway rest stops behind concrete walls, or rural areas. Switch between mobile data and Wi-Fi, or walk to a spot with better signal and load the charger details there.

2. 2

   Force-close the app and reopen it

   Swipe the EnBW mobility+ app away from your recent apps list, wait a few seconds, and reopen it. Navigate to the charger again. This clears any stuck network requests.

3. 3

   Search for the charger by ID

   Instead of tapping the map pin, use the search bar in the app and enter the charger's ID or EVSE number (printed on the physical unit). This sometimes loads details that the map view fails to fetch.

4. 4

   Use the QR code on the charger as a backup

   Many chargers have a QR code that opens a direct session start page. Scan it with your phone camera. This page is served by the CPO, not EnBW, and often loads faster.

5. 5

   Clear the app cache

   On Android: Settings, Apps, EnBW mobility+, Storage, Clear Cache. On iOS: delete and reinstall the app (iOS does not offer cache clearing). This resolves issues caused by corrupted local data.

QR code scan not working

You scan the QR code on the charger with the EnBW mobility+ app and it either does not recognize the code, opens a wrong page, or shows an error.

Symptoms

• App says 'QR code not recognized' after scanning
• QR code opens a web page for the CPO's own app instead of EnBW mobility+
• Camera does not focus on the QR code (too dark, code damaged)
• Scan succeeds but the session start page shows an error

How to Fix It

1. 1

   Use the EnBW app's built-in scanner, not your phone camera

   Open the EnBW mobility+ app and use its QR scanner (usually in the top menu or via a scan button on the map screen). Scanning with your phone camera might open the CPO's own page instead of routing through EnBW.

2. 2

   Clean the QR code

   Wipe dirt, rain, or ice off the QR code with your sleeve. Damaged or faded QR codes are common on outdoor chargers. If the code is badly worn, look for a second QR code on a different part of the charger.

3. 3

   Turn on your phone's flashlight

   In dark or shaded areas, the camera cannot read the code. Most QR scanners (including EnBW's) have a flashlight toggle. Enable it for better readability.

4. 4

   Enter the charger ID manually

   If the QR code will not scan, look for the charger's numeric or alphanumeric ID printed nearby. Enter it manually in the EnBW app's search function to find and start the session.

Cannot stop the session from the app

You tap 'Stop Charging' in the EnBW mobility+ app and nothing happens. The session keeps running, your car keeps charging (or has already finished but the session stays active), and you want to unplug and leave.

Symptoms

• 'Stop' button in the app does not respond or shows an error
• Session shows as active in the app even after unplugging
• Charger screen says 'Session active' but your car is full
• You are worried about accumulating idle fees

How to Fix It

1. 1

   Physically unplug the connector from your car

   On most chargers, unplugging the cable ends the session automatically, regardless of what the app says. Unlock your car's charge port (from the car's screen, key fob, or charge port button) and remove the connector.

2. 2

   Wait 2 minutes and check the app again

   There is often a delay between physically ending the session and the app updating. The app depends on the CPO's system sending a 'session ended' signal back through the roaming chain. Give it a moment.

3. 3

   Force-close and reopen the app

   Sometimes the app's session view gets stuck. Force-close it, reopen, and check your session history. The session may already be ended on the backend even if the active session screen was not updating.

4. 4

   Press the stop button on the charger itself

   Many chargers have a physical stop button on the screen or housing. Press it. This sends the stop command directly to the charger hardware without going through the roaming network.

5. 5

   Contact support if you are being billed for a stuck session

   If the session stays 'active' in the app for more than 10 minutes after you have unplugged and driven away, contact EnBW mobility+ support. They can close the session on their end and correct any overcharges.

App is in German and hard to navigate

The EnBW mobility+ app defaults to German. If you do not speak German, navigating menus, understanding pricing details, and finding settings can be frustrating.

Symptoms

• All menus and buttons are in German after installation
• Language setting not obvious in the app
• Error messages appear in German, making troubleshooting difficult
• Pricing terms and tariff explanations are only in German

How to Fix It

1. 1

   Change your phone's system language temporarily

   The EnBW mobility+ app follows your phone's system language. If English is available in the app, switching your phone to English (Settings, General, Language) will switch the app too. You can switch back after you finish.

2. 2

   Check for an English option in the app settings

   Open the app, tap the profile or menu icon (usually three lines or a person icon in the corner), and look for 'Sprache' (Language) or 'Einstellungen' (Settings). Some versions offer English as an option directly.

3. 3

   Use your phone's translate feature on screenshots

   On iOS, take a screenshot and use Live Text to translate. On Android, use Google Lens. This is useful for understanding pricing details or error messages in German.

4. 4

   Consider an alternative roaming app with better language support

   If the language barrier is a persistent problem, apps like Shell Recharge, Plugsurfing, or Chargemap offer similar roaming coverage across Europe and have full English interfaces. They access many of the same chargers.