Honda e:Ny1 Charging at ChargePoint

Honda e Ny1 Charger Will Not Start a Charging Session

You have connected the charger to your Honda e:Ny1, but the session is not starting. The screen is blank, there is an error, or the car just does not respond. As Honda's first mass-market European EV, the e:Ny1 uses standard connectors but has a few quirks worth knowing.

Symptoms

• The CCS2 or Type 2 connector is plugged in but no charging begins
• The Honda e:Ny1's instrument cluster does not show a charging indicator
• The charger screen shows an error code after plug-in
• You hear the connector lock engage but power does not flow
• The charging app shows the session failed to start

What to Do

1. 1

   Authenticate before plugging in

   Tap your RFID card or start the session in the charging app before inserting the connector. Wait for the charger screen to show 'ready' or 'plug in now.'

2. 2

   Unplug and firmly reinsert

   Remove the connector completely from the e:Ny1's charge port on the front right. Wait 10 seconds, then reinsert it firmly until you hear the locking click.

3. 3

   Check for a charging timer

   On the Honda e:Ny1's dashboard, navigate to the charging settings and check if a timer is active. Disable it if you need to charge immediately.

4. 4

   Reset the car's charging system

   Turn the car off, lock it with the key fob, wait 30 seconds, then unlock and try again. This can clear any error state from a previously interrupted session.

5. 5

   Inspect the charge port

   Check the charge port for moisture, dirt, or debris. Clean it gently with a dry cloth if needed. Make sure the port flap opens fully.

6. 6

   Try a different charger

   If the charger still will not start after trying all steps, move to a different unit. The charger is more likely to be the problem than the car.

Honda e Ny1 Payment Not Working at Charging Station

You are at a charger with your Honda e:Ny1 and the payment is not going through. Card declined, app not working, RFID not recognized. This has nothing to do with your car. It is a charger and payment network problem. Here is how to get past it.

Symptoms

• RFID card tap produces no response from the charger
• Charging app shows a payment authorization error
• Bank card is declined at the charger terminal
• Charger screen shows 'payment failed' or a generic error
• You cannot find any accepted payment method on the charger

What to Do

1. 1

   Check which payments the charger accepts

   Look at the charger screen and stickers for accepted payment methods. If none of your options are listed, you need to move to a different charger or sign up for that network.

2. 2

   Try a different payment method

   Switch between RFID card, charging app, and contactless bank card. If one method fails, another may work on the same charger.

3. 3

   Verify your card balance

   Open your banking app and check that you have at least 80 EUR available. Top up or switch to a card with more available balance if needed.

4. 4

   Hold the RFID card steadily for 3 seconds

   Place the card flat on the reader and hold it without moving. Some readers are slow and need a longer contact time to register.

5. 5

   Update your charging app payment details

   Open each charging app you use and check that the stored payment method is current. Update any expired cards.

6. 6

   Move to another charger unit

   If nothing works on this charger, try the next unit at the same station. Individual card readers fail while other units work fine.

Honda e Ny1 Charging Slower Than Expected DC and AC

You plugged in your Honda e:Ny1 expecting fast charging, but the speed is disappointing. The e:Ny1 tops out at 78 kW DC, which is slower than many competitors. Without preconditioning or a heat pump, cold weather makes it worse. Here is what is happening and what you can do.

Symptoms

• DC fast charging well below the 78 kW maximum
• AC home charging stuck at 3-4 kW instead of 11 kW
• Charging speed drops significantly after 50% state of charge
• Cold weather charging is extremely slow
• Charging from 10% to 80% takes much longer than expected

What to Do

1. 1

   Drive before charging in cold weather

   Since the e:Ny1 has no preconditioning, drive for 20-30 minutes before stopping at a DC charger in winter. The driving warms the battery through use, which improves charging acceptance.

2. 2

   Check your state of charge

   For the best speeds, arrive at the charger between 10-20% and charge to 80%. The e:Ny1's peak power is available mainly below 50%.

3. 3

   Choose a charger rated above 100 kW

   Even though the e:Ny1 maxes out at 78 kW, using a higher-rated charger ensures you are not bottlenecked by the charger. Avoid 50 kW units when faster options are available.

4. 4

   Verify your AC installation

   For home charging, confirm with your electrician that your wallbox is wired for three-phase at 16A to deliver the full 11 kW. Single-phase installations will be about a third of that speed.

5. 5

   Check if the charger is sharing power

   Look at the charger. If two cables come from the same unit and someone is using the other one, you may be sharing power. Move to a solo charger if possible.

6. 6

   Try a different charger

   If your speed is still well below 60-70 kW at a low state of charge and warm battery, the charger may be degraded. Test a different unit.

App shows "Available" but the charger is physically broken

The ChargePoint app shows a green status for a charger, but when you arrive, the unit is visibly damaged, has a blank screen, or displays an out-of-service message. This happens because ChargePoint's availability status depends on the charger reporting its own state, and a broken charger sometimes cannot report that it is broken.

Symptoms

• App shows the charger as available with a green icon
• Charger screen is blank, cracked, or showing an error message on site
• The connector is physically damaged or the cable is severed
• Other drivers at the station confirm the charger has been broken for days

How to Fix It

1. 1

   Check the other chargers at the same station

   ChargePoint stations often have multiple units. If one is broken, another unit nearby may work fine. Use the app to see all connectors at the location.

2. 2

   Report the broken charger in the ChargePoint app

   Open the station detail in the ChargePoint app, find the specific charger, and report the issue. Select the most accurate problem description. This updates the status for other drivers and alerts the station operator.

3. 3

   Check recent driver reports in the app

   The ChargePoint app sometimes shows recent check-ins or reports from other drivers. Before driving to a station, scroll down on the station detail page to see if anyone has reported issues recently.

4. 4

   Find the nearest alternative station

   In the ChargePoint app, tap "Find nearby" or zoom out on the map. Filter for DC fast chargers if you need speed. You can also check Google Maps or A Better Route Planner for non-ChargePoint alternatives.

RFID tap not registering

You tap your ChargePoint card on the reader and nothing happens. No beep, no screen change, no session. The RFID readers on ChargePoint stations can be finicky, especially on older European units.

Symptoms

• Tapping the RFID card produces no response from the charger
• The charger beeps but then shows "Authentication failed"
• The card works at some ChargePoint stations but not this one
• The RFID reader area is hard to locate on the charger

How to Fix It

1. 1

   Find the correct RFID reader location

   On ChargePoint stations, the RFID reader is sometimes in an unexpected spot. Look for a small RFID symbol, usually on the front face of the charger or near the screen. On some European units, it is on the side panel.

2. 2

   Hold the card flat and steady for three seconds

   Do not tap and pull away quickly. Press the card flat against the reader area and hold it still for a full three seconds. Some readers need this extra time.

3. 3

   Remove your card from any wallet or phone case

   If your ChargePoint card is in a wallet with other RFID cards or near your phone, interference can prevent the reader from detecting it. Hold the card alone against the reader.

4. 4

   Start the session from the ChargePoint app instead

   Open the ChargePoint app, find the station, select the specific charger, and tap "Start." This sends a start command over the network and does not rely on the physical RFID reader at all.

5. 5

   Check if your card is activated

   New ChargePoint RFID cards need to be activated in the ChargePoint app or on the website. Go to Account, then Cards, and verify your card is listed and active.

Session auto-terminates at 80%

Your charging session stops automatically when your battery reaches around 80%, even though you did not set a limit and wanted to charge further. Some ChargePoint stations, particularly those operated by local CPOs, have a configuration that ends sessions at 80% to free up the charger for the next driver.

Symptoms

• Charging stops at exactly 80% state of charge
• The ChargePoint app shows the session as "Complete" at 80%
• No error message on the charger, it simply stops
• Your car is still ready to accept more charge

How to Fix It

1. 1

   Check if this is a station policy

   Some station operators set an 80% cutoff on DC fast chargers to maximize charger availability. This is not a fault. Check the station detail in the ChargePoint app or look for signage at the station explaining time or charge limits.

2. 2

   Start a new session

   After the session ends at 80%, you can often start a new session on the same charger to continue charging. Unplug, wait 10 seconds, plug back in, and authenticate again.

3. 3

   Check your car's own charge limit

   Some EVs have a default charge limit set to 80% in the car's settings. Check your car's infotainment system under charging settings. If the limit is set to 80%, the car itself is stopping the session, not ChargePoint.

4. 4

   Switch to a different station if you need to charge above 80%

   If the 80% cutoff is a station policy and you need more charge, find a station without this restriction. AC chargers at destinations are usually a better choice for topping up above 80% because DC charging is very slow above that level anyway.

Waitlist feature not working

ChargePoint offers a waitlist feature that is supposed to notify you when a busy charger becomes available. In practice, the notifications are unreliable, especially at European stations.

Symptoms

• You joined the waitlist but never received a notification
• The notification arrived long after the charger became available
• The waitlist button is not available for some stations
• You received a notification but the charger was already taken by someone else

How to Fix It

1. 1

   Enable push notifications for the ChargePoint app

   Go to your phone's notification settings and make sure ChargePoint notifications are allowed. On iOS, check Settings, then Notifications, then ChargePoint. On Android, check App Info, then Notifications.

2. 2

   Stay within a reasonable distance of the station

   The waitlist is most useful when you are nearby, at a shop or restaurant within a few minutes of the charger. By the time you drive 15 minutes back to a station, the charger may already be taken again.

3. 3

   Do not rely solely on the waitlist

   Treat the waitlist as a nice-to-have, not a guarantee. Check the app manually every few minutes for availability updates, or look for an alternative station while you wait.

4. 4

   Check if the station supports the waitlist feature

   Not all ChargePoint stations have the waitlist enabled, particularly CPO-operated stations using ChargePoint hardware. If you do not see a waitlist option on the station page, the feature is not available there.

App interface confusing for European users

ChargePoint's app was designed primarily for the US market. European users sometimes encounter US-centric defaults, unfamiliar terminology, or features that do not apply in Europe.

Symptoms

• App defaults to miles instead of kilometers
• Pricing displayed in unexpected formats or currencies
• Filter options include connector types not used in Europe, like NACS
• Station details reference US-specific payment methods or loyalty programs
• Map loads centered on the US instead of your actual location

How to Fix It

1. 1

   Set your region and units in the app settings

   Open the ChargePoint app, go to Account or Settings, and look for region, language, or unit preferences. Set distance to kilometers and currency to your local currency.

2. 2

   Filter for CCS2 connectors

   When searching for stations, use the filter to show only CCS2 (the European DC fast charging standard). This hides US-only connector types from your results.

3. 3

   Check the station detail for European pricing

   Tap on a station to see the pricing breakdown. European ChargePoint stations typically show pricing in EUR, SEK, NOK, or GBP per kWh, sometimes with an additional per-minute fee after a certain duration.

4. 4

   Ignore US-specific features

   Features like ChargePoint Home integration or certain fleet management tools are designed for the US market. If something in the app does not seem relevant, it probably is not meant for European users.

CPO-operated station behaves differently than expected

Some stations use ChargePoint hardware and appear in the ChargePoint app, but they are owned and operated by a local charge point operator. These stations may have different pricing, access rules, or session limits than ChargePoint-owned stations.

Symptoms

• Pricing at the station does not match what you expected from ChargePoint
• Your ChargePoint account works but the session has unexpected restrictions
• The charger looks like ChargePoint but has another company's branding on it
• Customer support refers you to a different company for this station

How to Fix It

1. 1

   Check who operates the station

   In the ChargePoint app, the station detail page usually shows the operator or network name. If it says something other than ChargePoint, the station is CPO-operated and may have its own rules.

2. 2

   Read the pricing and terms on the station detail page

   CPO-operated stations set their own pricing. Check the ChargePoint app for the exact per-kWh rate and any time-based fees or session limits before you plug in.

3. 3

   Try the CPO's own app if ChargePoint authentication fails

   Some CPO stations accept ChargePoint cards but work more reliably with the operator's own app or RFID card. Look for the operator's name on the charger and download their app.

4. 4

   Contact the station operator for site-specific issues

   For problems like broken hardware, pricing errors, or access restrictions at a CPO-operated station, contact the operator directly. Their contact information is usually on the charger or in the station detail in the ChargePoint app.