Citroen e-C4 Charging at Recharge

Citroen e-C4 Charger Won't Start? Step-by-Step Fix

Your Citroen e-C4 is connected to the charger but nothing is happening. No power, no progress, and maybe an error flashing on the charger screen. This is a common problem at public charging stations and it usually has a straightforward fix.

Symptoms

• CCS2 connector inserted but no charging session begins
• Charger screen shows an error code or connection failure
• The e-C4's charge port indicator does not light up or blinks red
• Charger starts to initialize but disconnects within seconds
• Type 2 connector locks in at an AC station but no power flows

What to Do

1. 1

   Complete the authentication step

   Tap your RFID card, start a session in the charging app, or use contactless payment. Follow the charger's on-screen instructions. Some networks require authentication before plugging in, others after.

2. 2

   Unplug and firmly reseat the connector

   Pull the CCS2 or Type 2 connector out completely and reinsert it straight into the charge port with a firm push until it clicks. Keep the cable aligned and support its weight.

3. 3

   Disable scheduled charging on the touchscreen

   Open the charging settings on the e-C4's central touchscreen. Turn off any scheduled or deferred charging mode so the car accepts power immediately.

4. 4

   Clean the charge port

   Check the charge port on the left rear for dirt, salt, or ice. Wipe the contacts with a dry cloth. In freezing weather, gently clear any ice from the port opening and door.

5. 5

   Lock and unlock the vehicle to reset

   Use the key fob or the MyCitroen app to lock the car, wait 10 seconds, then unlock it. This resets the charge port controller. Try plugging in again.

6. 6

   Try a different charger

   Move to another stall at the same station or find a nearby alternative. Some charger faults affect only one unit while others at the same site work fine.

Citroen e-C4: Charger Payment Failed? Quick Fixes

Your Citroen e-C4 is plugged in, but the payment is not going through. RFID rejected, app error, or bank card declined. This is entirely a charger and payment issue, not a car problem. Here is how to sort it out and start charging.

Symptoms

• RFID card rejected with an error beep or message
• Charging network app shows a payment error or session failure
• Contactless bank card declined at the charger terminal
• Pre-authorization hold appears but no charging session starts
• Charger starts briefly then stops with a billing error

What to Do

1. 1

   Check accepted payment methods on the charger

   Look at the charger's display and body for logos showing which RFID networks, apps, or card payment options are accepted.

2. 2

   Try a different payment method

   Switch from RFID to the network app, or from the app to a contactless bank card. Always carry at least two options.

3. 3

   Check your bank card balance

   Open your banking app and confirm you have enough available balance for a pre-authorization hold. Some chargers hold up to 80 EUR upfront.

4. 4

   Update or restart the charging app

   Check for updates, close and reopen the app, and look for any stuck open sessions. Log out and back in if the problem persists.

5. 5

   Use the charger's built-in card reader

   Look for a contactless card reader on the charger. More European stations now offer direct bank card payment, which bypasses RFID and app issues.

6. 6

   Call the support number on the charger

   Every public charger displays a support number. The operator can sometimes start a session remotely or diagnose the payment issue from their end.

Citroen e-C4 Charging Too Slow? How to Fix It Now

Your Citroen e-C4 can charge at up to 100 kW on a DC fast charger, but you might be getting far less. The 50.8 kWh NMC battery sits on the Stellantis e-CMP platform, and its charging behavior has some known limitations. Here is what holds back your speed and how to work around it.

Symptoms

• DC charging power stays well below 100 kW even at a high-power station
• Charging speed drops steeply before reaching 50% state of charge
• AC charging at home maxes out at 3.6 kW instead of 11 kW
• The touchscreen shows an estimated time much longer than expected
• Cold weather charging sessions take nearly twice as long as summer sessions

What to Do

1. 1

   Drive at highway speed for 15-20 minutes before fast charging

   Since the e-C4 has no battery preconditioning, active driving is the best way to warm the battery. Highway driving before your charging stop makes a meaningful difference in cold weather charging speeds.

2. 2

   Arrive at the charger between 10% and 20%

   The e-C4 charges fastest at low state of charge. Plan your stop so you arrive around 10-15% to take advantage of peak speeds. The difference between 10% and 50% arrival can be 30-40 kW.

3. 3

   Pick a charger stall that is not sharing power

   Check if two CCS2 cables come from one cabinet. Choose the stall where the other connector is free. This ensures you get the full power output from the charger.

4. 4

   Verify your home AC setup

   Check the power reading on the e-C4's touchscreen during a home AC charge. If it shows about 3.6 kW, you are on single-phase power. A three-phase upgrade unlocks the full 11 kW.

5. 5

   Monitor the charging screen

   During DC charging, watch the current power on the touchscreen. If it starts low, the battery may be warming up. Give it 5-10 minutes. Power should gradually increase as the battery temperature rises.

6. 6

   Stop DC charging at 80% on road trips

   The last 20% takes disproportionately long. On longer drives, unplug at 80% and drive to the next charging stop. You will save significant time overall.

Charger stuck in "preparing" state

You authenticated successfully, the charger says "preparing," but it never starts delivering power. This is one of the most reported issues on Recharge stations, especially at older units.

Symptoms

• Charger screen shows "Preparing" or "Initializing" for more than two minutes
• Your car's charging indicator does not activate
• The Recharge app shows the session as active but 0 kW delivered
• The charger fan spins up but no power flows

How to Fix It

1. 1

   Wait up to three minutes

   Some Recharge units, particularly the 300kW stations, take longer to complete the power handshake with your car. Give it a full three minutes before taking action.

2. 2

   Unplug and reconnect

   Remove the CCS2 connector, wait 15 seconds, then plug it back in firmly. This resets the communication between your car and the charger.

3. 3

   Stop the session in the Recharge app and start a new one

   Open the Recharge app, tap Stop on the active session, wait for it to fully end, then start a new session on the same charger. This clears any stuck state on the backend.

4. 4

   Try the other connector on the same unit

   Many Recharge stations have two CCS2 connectors. If one is stuck, the other connector on the same unit often works fine.

5. 5

   Use a different authentication method

   If you started with the app, try your RFID card instead, or vice versa. Sometimes the issue is with the authentication path, not the charger hardware.

Old Fortum branding causes app scan failure

Recharge was originally part of Fortum's charging operations before being spun off as a separate company. Some older stations still display Fortum logos and QR codes. Scanning an old Fortum QR code with the Recharge app may not work, or it may redirect to a dead Fortum page.

Symptoms

• QR code on the charger opens a Fortum website or shows an error
• Recharge app says "Charger not found" after scanning
• Station ID on the physical unit does not match what the Recharge app expects
• The charger has Fortum branding but is listed as Recharge in third-party apps

How to Fix It

1. 1

   Ignore the QR code and search by station name in the Recharge app

   Open the Recharge app, use the map or search to find the station by location. The charger will appear under its Recharge name even if the physical unit still says Fortum.

2. 2

   Enter the charger ID manually

   Look for a numeric ID on the charger, often printed on a sticker near the connector. In the Recharge app, tap "Enter ID" and type it in directly.

3. 3

   Use RFID or contactless payment instead of the app

   Tap your Recharge RFID card or a contactless bank card on the reader. This bypasses the app entirely and works regardless of the branding on the charger.

4. 4

   Check if contactless is available on this unit

   Not all Recharge stations support contactless bank card payment. Look for a card reader terminal on the charger. If there is no terminal, you will need the app or an RFID card.

RFID card from old Fortum account not recognized

If you had a Fortum Charge & Drive account and RFID card, it may not work automatically on the Recharge network. Some cards were migrated, others were not.

Symptoms

• Tapping your old Fortum RFID card shows "Card not recognized" on the charger
• The charger beeps but does not start a session
• Your Fortum card works on some stations but not others

How to Fix It

1. 1

   Log in to the Recharge app and check your RFID cards

   Open the Recharge app, go to your account settings, and look under RFID cards. If your old Fortum card is not listed, it was not migrated automatically.

2. 2

   Re-register your RFID card

   In the Recharge app, tap "Add RFID card" and follow the steps. You will need the card number printed on the back of your RFID card.

3. 3

   Use the app to start the session while you wait for RFID activation

   RFID card registration can take up to 24 hours to propagate across all stations. Use the app to authenticate in the meantime.

4. 4

   Order a new Recharge RFID card if re-registration fails

   Some older Fortum cards use a chip format that is not compatible. You can order a new Recharge RFID card through the app or website.

Contactless payment not accepted

You are trying to tap your bank card or phone to pay, but the charger does not respond or shows an error. Contactless payment availability varies across Recharge stations.

Symptoms

• No card reader terminal visible on the charger
• Card reader shows "Payment failed" or does not respond to taps
• Apple Pay or Google Pay not recognized
• The charger prompts for an RFID card but you only have a bank card

How to Fix It

1. 1

   Check if this station supports contactless payment

   Look for a separate payment terminal with a contactless symbol. Not all Recharge stations have been upgraded. The Recharge app shows payment options for each station on the station detail page.

2. 2

   Try removing and re-holding your card

   Hold your card flat against the reader for at least three seconds. Some terminals need a longer hold than you might expect. Remove the card fully, then try again.

3. 3

   Fall back to the Recharge app

   If contactless is not working, open the Recharge app and start the session from there. You need a payment method saved in the app.

4. 4

   Try a different card

   Some Visa Electron and certain prepaid cards are not accepted by the payment terminals. A standard Visa or Mastercard debit or credit card usually works.

Charging speed much lower than expected

The station is rated for 300kW, but your car is only pulling 50kW or less. While your car's battery management limits the maximum speed, Recharge stations can also throttle power.

Symptoms

• Charger display shows far less power than the station's rated capacity
• Charging speed drops suddenly mid-session
• Other cars at the same station are also charging slowly
• The Recharge app shows the session but at low power

How to Fix It

1. 1

   Check how many other cars are charging at the same station

   Recharge stations with multiple connectors often share a power cabinet. If two or three cars are charging simultaneously, the available power per car drops. This is normal and not a fault.

2. 2

   Check your battery level

   DC fast charging slows significantly above 80% on most EVs. If your battery is above 70-80%, the slower speed is your car protecting the battery, not a problem with the Recharge station.

3. 3

   Check the temperature

   In cold weather, your car may limit charging speed until the battery warms up. This can take 10-15 minutes of charging before speeds increase. Some cars precondition the battery if you set the charger as a destination in navigation.

4. 4

   Try a different connector at the station

   Individual connectors can have faults that limit power output. If another connector is free, unplug and try it.

5. 5

   Report the issue in the Recharge app

   If the speed is unusually low and none of the above apply, report it through the Recharge app. Tap the active session and look for a "Report issue" option. This helps Recharge identify hardware problems.