Citroën ë-Berlingo Charging at Atlante

Citroën ë-Berlingo Charger Will Not Start Charging

You plugged in the CCS2 cable, the app says the session started, but nothing is happening. Or you tapped your card and the charger just blinks without delivering power. This is frustrating when you need to get back on your delivery route. Most charger start failures on the ë-Berlingo come down to authentication, cable locking, or the charger itself.

Symptoms

• CCS2 connector plugged in but charger shows no active session
• Charger display shows an error code after tapping RFID card or using the app
• Dashboard shows the charge port is connected but charging does not begin
• Cable does not lock into the CCS2 port on the ë-Berlingo
• Charger starts briefly then immediately stops with an error

What to Do

1. 1

   Remove and reseat the CCS2 connector

   Pull the connector out completely, wait 10 seconds, and push it back in firmly until you hear or feel a click. Make sure the charge port flap is fully open and nothing is blocking the port.

2. 2

   Check for a charging schedule

   On the ë-Berlingo's touchscreen, go to the charging settings. If a charging schedule is active, disable it or select "Charge now" to override the timer.

3. 3

   Re-authenticate with the charger

   End any active session in the charging app, then start a new session. If using RFID, hold the card steady against the reader for 3-4 seconds. Some chargers require you to authenticate before plugging in, not after.

4. 4

   Check the charger status on the network app

   Open the charging network's app and check if the charger is showing as available. If it shows an error or offline status, do not waste time troubleshooting. Move to a different charger.

5. 5

   Try the other connector or stall

   If the charger has two stalls or both a CCS2 and CHAdeMO connector, try the other option. Sometimes one stall works while the other is faulty.

6. 6

   Restart the vehicle systems

   Turn the ë-Berlingo fully off, wait 30 seconds, then turn it back on. Unplug and replug the cable. This resets the charging communication between the car and the charger.

Citroën ë-Berlingo Charging Payment Failed at DC

You tapped your card, the charger beeped, and then showed a payment error. Or the app keeps spinning without starting the session. Payment failures at public chargers are rarely about your ë-Berlingo. They are almost always about the charging network, your payment method, or mobile signal. Here is how to get charging and get back on your route.

Symptoms

• Charger displays a payment error or 'transaction declined' message
• Charging app shows 'session failed to start' after payment attempt
• RFID card is not recognized by the charger reader
• Contactless bank card payment does not register
• Charger starts the authorization process but times out before delivering power

What to Do

1. 1

   Try a different payment method

   If your RFID card failed, try the charging app. If the app failed, try a contactless bank card directly on the charger's reader. Having two or three payment options saves time when one does not work.

2. 2

   Check your mobile signal

   Look at your phone's signal indicator. If you have weak or no signal, the app cannot communicate with the charger. Try moving your phone closer to the charger or stepping away from walls and structures that block signal.

3. 3

   Verify your payment details in the app

   Open the charging app and check your payment method. Make sure your card has not expired and that there are no pending issues. Update your card details if needed.

4. 4

   Check which networks the charger accepts

   Look at the charger or surrounding signage for logos of accepted charging networks. If your provider is not listed, you may need to use a different app or card that has a roaming agreement with this charger.

5. 5

   Contact your fleet manager or charging provider

   If you are using a company-provided RFID card and it does not work, the card may be deactivated or restricted. Contact your fleet manager or the charging provider's support line. Most providers have a number printed on the RFID card.

6. 6

   Use an alternative charger nearby

   If payment is not working at this station, check your app for the nearest alternative charger on your route. Do not spend too long troubleshooting a single charger when another one is nearby.

Citroën ë-Berlingo Charging Slower Than Expected

You stopped for a quick top-up between deliveries and the charger shows 20 kW instead of the 100 kW you expected. The ë-Berlingo's 50 kWh battery can charge at up to 100 kW on DC, but real-world speeds depend on temperature, state of charge, and the charger itself. Slow charging is rarely a defect. It is usually something you can identify and sometimes fix on the spot.

Symptoms

• DC fast charging speed well below the 100 kW maximum
• AC charging stuck at 3-4 kW instead of the full 11 kW
• Charging speed drops sharply after reaching 50-60% on the dashboard
• Charging session starts at a decent speed then slows down within minutes
• Charger display shows lower power than its rated output

What to Do

1. 1

   Check the battery temperature indicator

   Look at the dashboard or the MyCitroën app for battery temperature information. If the battery is cold, driving for 15-20 minutes before charging can help. The ë-Berlingo does not precondition the battery automatically, so plan your charging stop after some driving rather than first thing in the morning.

2. 2

   Check your state of charge

   Look at the battery percentage on the dashboard. If you are above 80%, the slower speed is expected. For the fastest charging during your delivery route, arrive at the charger between 10-20% and charge to 80%.

3. 3

   Verify the charger is not sharing power

   Look at the charger unit. If there are two cables and someone is using the other one, you may be sharing power. Move to an unoccupied charger if one is available.

4. 4

   Check the AC charge current setting

   On the ë-Berlingo's touchscreen, check the charging settings. Make sure the AC charge current is set to maximum. A reduced setting will limit your depot or home charging speed.

5. 5

   Confirm your wallbox phase configuration

   If depot charging seems slow, ask your facility manager or electrician to verify the wallbox is wired for 3-phase power. Single-phase limits you to about 3.7 kW, which means roughly 14 hours for a full charge instead of about 5 hours.

6. 6

   Try a different charger

   If the speed is still low on DC, the charger itself may be degraded or faulty. Try a different stall at the same location or a different charging station on your route.

New station with teething problems

Atlante is expanding rapidly, and many stations are brand new. Newly installed chargers sometimes have firmware bugs, incomplete network configuration, or hardware that has not been fully tested under real-world conditions.

Symptoms

• Charger turns on but fails to communicate with your vehicle
• Session starts but drops after a few seconds
• Charger screen shows an error code you have never seen before
• Station appears on the map but the chargers are not yet operational

How to Fix It

1. 1

   Try a different charger at the same station

   New stations often have multiple units and the issue may be limited to one charger. Try another unit before giving up on the location.

2. 2

   Unplug, wait 30 seconds, and retry

   New charger firmware sometimes fails on the first handshake but succeeds on the second attempt. A short wait lets the charger reset its session state.

3. 3

   Start the session through the Atlante app

   If the charger's screen or contactless reader is not working properly, the app provides a separate communication path to the charger's backend. This can bypass local hardware issues.

4. 4

   Check the Atlante app for station status notes

   Atlante sometimes posts notices about newly activated stations that are still in testing. The station detail page in the app may show a note about limited functionality.

5. 5

   Report the issue and move to the next station

   Use the Atlante app to report the problem. New station issues are usually fixed quickly once reported. Check the app for the nearest alternative Atlante or competitor station.

App crashes on older phones

The Atlante app can be unstable on older phones or phones running outdated operating systems. The app may crash during login, while loading the map, or in the middle of starting a session.

Symptoms

• App closes unexpectedly when you open the station map
• App freezes during the payment screen
• Login screen loads but the app crashes after entering credentials
• App works briefly but crashes when you try to start a session

How to Fix It

1. 1

   Update the Atlante app to the latest version

   Atlante pushes frequent updates that fix stability issues. Open the App Store or Google Play and check for updates before your trip.

2. 2

   Clear the app cache

   On Android, go to Settings, Apps, Atlante, and clear the cache. On iPhone, delete and reinstall the app. Corrupted cache data is a common cause of crashes.

3. 3

   Check your phone's operating system version

   The Atlante app may require iOS 15+ or Android 10+. If your phone is on an older version, update if possible. If your phone cannot update, you may need a roaming app as a backup.

4. 4

   Use contactless payment as a fallback

   If the app keeps crashing and the station supports contactless, tap your credit or debit card on the charger's payment terminal. Not all Atlante stations have this yet, but it completely bypasses the app.

5. 5

   Try a roaming app

   Apps like Chargemap, Shell Recharge, or Electropass can start sessions at Atlante stations without using the Atlante app. Check roaming coverage before relying on this.

Contactless payment terminal not activated

Atlante is rolling out contactless card payment across its network, but not every charger has an active terminal yet. Some units have the hardware installed but the payment function is not turned on.

Symptoms

• Card reader is visible on the charger but does not respond to a tap
• Screen says 'Use app to start' with no contactless option shown
• Contactless symbol is printed on the charger but the reader light is off
• You see a payment terminal but tapping produces no response

How to Fix It

1. 1

   Download and use the Atlante app

   At stations where contactless is not yet active, the Atlante app is the primary payment method. Download it before your trip and add a payment card in advance.

2. 2

   Check the charger screen for payment instructions

   Some Atlante chargers display which payment methods are currently available. If contactless is not listed, the terminal is not active at that unit.

3. 3

   Try a different charger at the same station

   Contactless activation sometimes rolls out unit by unit. Another charger at the same station may have an active terminal.

4. 4

   Use a roaming RFID card or app

   If you have an RFID card from a roaming provider, try tapping it. Some Atlante stations accept roaming RFID even when the contactless card terminal is not active.

Charger screen hard to read in direct sunlight

Some Atlante charger screens have low brightness levels that make them nearly impossible to read in bright sunlight. This is especially common at stations in Southern Europe during summer.

Symptoms

• Screen content is barely visible outdoors during the day
• You cannot read the price, status, or error messages on the screen
• Screen appears to be off but the charger is actually on
• You have to cup your hands around the screen to read it

How to Fix It

1. 1

   Use your body or hand to shade the screen

   Stand to block direct sunlight from hitting the screen. Even partial shade can make the display readable.

2. 2

   Take a photo of the screen with your phone

   Your phone camera can sometimes capture what your eyes cannot. Take a photo and zoom in to read the text.

3. 3

   Use the Atlante app to monitor your session

   All session information (charging speed, energy delivered, cost, estimated time) is available in the app. You do not need the charger screen to track your session.

4. 4

   Start the session entirely through the app

   If you cannot read the screen at all, use the Atlante app to select the charger, start the session, and stop it when done. This avoids needing to interact with the screen.

Cable connector requires specific angle to lock

Some Atlante charger cables need to be inserted at a particular angle or with extra force for the CCS2 connector to seat properly. If it is not fully locked, the session will not start.

Symptoms

• Connector feels like it is in but the charger does not recognize it
• Charger screen says 'Connect cable' even though the cable is plugged in
• You hear a partial click but the connector is not locked
• Connector slides back out after you let go

How to Fix It

1. 1

   Push the connector straight in, then slightly upward

   Some Atlante CCS2 connectors need a slight upward tilt after the initial push to engage the locking mechanism. You should feel and hear a solid click.

2. 2

   Check for debris in the vehicle's charging port

   Dust, ice, or a small pebble in the port can prevent the connector from seating fully. Inspect the port and brush out anything you find.

3. 3

   Make sure the vehicle is unlocked and ready to charge

   Some vehicles lock the charging port flap or disable the inlet when the car is locked or in drive mode. Ensure the car is in park and unlocked.

4. 4

   Try a different cable if the charger has two

   If the charger has two CCS2 cables, try the other one. One cable may have a slightly worn connector that does not seat as easily.