BMW i4 Charging at ChargePoint

BMW i4 Charger Won't Start? Step-by-Step Solutions

You've plugged in the CCS2 cable to your BMW i4's right rear charge port, but nothing happens. This is one of the most common frustrations at public chargers. The good news is that most causes are fixable on the spot.

Symptoms

• CCS2 connector is plugged into the right rear port but the charger screen shows no vehicle detected
• Charger displays an error code and refuses to start the session
• My BMW app shows the car is plugged in but not charging
• The charge port LED on the i4 flashes or stays amber instead of turning blue
• Authentication via app or RFID card goes through but charging never begins

What to Do

1. 1

   Unplug the CCS2 cable and reseat it firmly

   Pull the connector out completely. Check the pins for debris or damage. Line it up straight with the charge port on the right rear and push until you hear a clear click. The charge port LED should respond.

2. 2

   Check the charge port LED color on the car

   Blue pulsing means the car is ready to charge. Amber or yellow means something is wrong on the car side. No light at all may mean the port isn't detecting the cable. Open the My BMW app for more detail.

3. 3

   Disable any charging schedule in iDrive

   On the iDrive curved display, go to the charging settings and check for active schedules or departure times. Disable scheduled charging temporarily if you want to charge immediately at a public station.

4. 4

   Try authenticating again or use a different method

   If Plug & Charge didn't start the session, open the charging network's app and start manually. If the app fails, try an RFID card. If you're using BMW Charging, check that your payment method is current in the My BMW app.

5. 5

   Restart the charger if possible

   Some chargers have a stop/reset button on the screen. Unplug, wait 30 seconds, and try again. If the charger has two cables, try the other connector. Check the charger's screen for error messages or an out-of-service notice.

6. 6

   Move to a different charger if the problem persists

   If nothing works after two attempts, the charger is likely faulty. Use the My BMW app or a charging map to find the next nearest station. Report the broken charger through the network's app to help other drivers.

BMW i4 Charging Payment Failed? How to Fix It Now

You're at the charger, the CCS2 cable is plugged into your BMW i4, but payment won't go through. Maybe Plug & Charge didn't kick in, the app is throwing errors, or your card was declined. Here's how to sort it out and start charging.

Symptoms

• Plug & Charge doesn't activate when you connect the CCS2 cable
• BMW Charging shows a payment error in the My BMW app
• The charger screen says authentication failed or payment declined
• Your RFID card is not recognized at this charging station
• Contactless card payment at the charger terminal is rejected

What to Do

1. 1

   Check if Plug & Charge is set up in the My BMW app

   Open the My BMW app, go to your charging settings, and verify that Plug & Charge is enabled and linked to an active payment method. If you see a setup prompt, complete it before trying again.

2. 2

   Update your payment method in BMW Charging

   In the My BMW app, navigate to your BMW Charging account and check your stored payment card. Update it if it's expired or recently replaced. The change should take effect within a few minutes.

3. 3

   Try the charging network's own app

   Identify which company operates the charger (the logo is usually on the unit). Download their app, create an account, add a payment method, and start the session through their app instead of BMW Charging.

4. 4

   Use a different RFID card or contactless payment

   If you have another RFID card from a different network, try that. Some chargers also accept contactless debit or credit cards. Look for a payment terminal on the charger, usually near the screen.

5. 5

   Try a different charger at the same station or a nearby station

   Sometimes a single charger's payment terminal malfunctions while others work fine. Try the next unit over. If the whole station is problematic, use iDrive navigation to find an alternative station nearby.

BMW i4 Charging Slower Than Expected? Fixes Here

Your BMW i4 eDrive40 supports up to 205 kW DC fast charging, but real-world speeds often fall short. Several factors specific to the i4's 80.7 kWh battery and 400V architecture can limit charging power. Here's how to diagnose and fix slow charging on your i4.

Symptoms

• DC charging speed stays well below 205 kW even at a high-power charger
• Charging curve drops sharply before reaching 60% state of charge
• AC charging at home or destination chargers maxes out at 3.6 kW instead of 11 kW
• iDrive curved display shows a lower charging rate than the charger's rated output
• Estimated charging time on the iDrive screen is much longer than expected

What to Do

1. 1

   Use iDrive navigation to route to your charging stop

   Enter the charging station as a waypoint or destination in iDrive. The i4 will automatically precondition the battery while you drive, warming it to the ideal temperature for fast charging. This alone can double your charging speed in cold weather.

2. 2

   Arrive at the charger with a lower state of charge

   The i4 charges fastest between 10% and 50%. If possible, plan your stop so you arrive closer to 10-20%. The difference between arriving at 15% versus 50% can save significant time.

3. 3

   Choose a charger stall that isn't sharing power

   Look at the charger setup. If two CCS2 cables come from one cabinet, pick a stall where the neighboring connector is free. Some stations label paired stalls with A/B designations.

4. 4

   Check your AC charging setup at home

   Open the My BMW app and look at the charging details during an AC session. If you're only getting 3.6 kW, your installation likely provides single-phase power. Ask your electrician about a three-phase connection to unlock the full 11 kW.

5. 5

   Check the charging status on the iDrive curved display

   While charging, the iDrive screen shows current power, estimated time remaining, and battery temperature. If power is low and battery temperature is also low, the car is still warming the pack. Give it a few minutes to ramp up.

6. 6

   Unplug at 80% and drive to the next charger if needed

   Charging from 80% to 100% on DC can take as long as 10% to 80%. On road trips, it's almost always faster to charge to 80%, drive, and stop again rather than waiting for a full charge.

App shows "Available" but the charger is physically broken

The ChargePoint app shows a green status for a charger, but when you arrive, the unit is visibly damaged, has a blank screen, or displays an out-of-service message. This happens because ChargePoint's availability status depends on the charger reporting its own state, and a broken charger sometimes cannot report that it is broken.

Symptoms

• App shows the charger as available with a green icon
• Charger screen is blank, cracked, or showing an error message on site
• The connector is physically damaged or the cable is severed
• Other drivers at the station confirm the charger has been broken for days

How to Fix It

1. 1

   Check the other chargers at the same station

   ChargePoint stations often have multiple units. If one is broken, another unit nearby may work fine. Use the app to see all connectors at the location.

2. 2

   Report the broken charger in the ChargePoint app

   Open the station detail in the ChargePoint app, find the specific charger, and report the issue. Select the most accurate problem description. This updates the status for other drivers and alerts the station operator.

3. 3

   Check recent driver reports in the app

   The ChargePoint app sometimes shows recent check-ins or reports from other drivers. Before driving to a station, scroll down on the station detail page to see if anyone has reported issues recently.

4. 4

   Find the nearest alternative station

   In the ChargePoint app, tap "Find nearby" or zoom out on the map. Filter for DC fast chargers if you need speed. You can also check Google Maps or A Better Route Planner for non-ChargePoint alternatives.

RFID tap not registering

You tap your ChargePoint card on the reader and nothing happens. No beep, no screen change, no session. The RFID readers on ChargePoint stations can be finicky, especially on older European units.

Symptoms

• Tapping the RFID card produces no response from the charger
• The charger beeps but then shows "Authentication failed"
• The card works at some ChargePoint stations but not this one
• The RFID reader area is hard to locate on the charger

How to Fix It

1. 1

   Find the correct RFID reader location

   On ChargePoint stations, the RFID reader is sometimes in an unexpected spot. Look for a small RFID symbol, usually on the front face of the charger or near the screen. On some European units, it is on the side panel.

2. 2

   Hold the card flat and steady for three seconds

   Do not tap and pull away quickly. Press the card flat against the reader area and hold it still for a full three seconds. Some readers need this extra time.

3. 3

   Remove your card from any wallet or phone case

   If your ChargePoint card is in a wallet with other RFID cards or near your phone, interference can prevent the reader from detecting it. Hold the card alone against the reader.

4. 4

   Start the session from the ChargePoint app instead

   Open the ChargePoint app, find the station, select the specific charger, and tap "Start." This sends a start command over the network and does not rely on the physical RFID reader at all.

5. 5

   Check if your card is activated

   New ChargePoint RFID cards need to be activated in the ChargePoint app or on the website. Go to Account, then Cards, and verify your card is listed and active.

Session auto-terminates at 80%

Your charging session stops automatically when your battery reaches around 80%, even though you did not set a limit and wanted to charge further. Some ChargePoint stations, particularly those operated by local CPOs, have a configuration that ends sessions at 80% to free up the charger for the next driver.

Symptoms

• Charging stops at exactly 80% state of charge
• The ChargePoint app shows the session as "Complete" at 80%
• No error message on the charger, it simply stops
• Your car is still ready to accept more charge

How to Fix It

1. 1

   Check if this is a station policy

   Some station operators set an 80% cutoff on DC fast chargers to maximize charger availability. This is not a fault. Check the station detail in the ChargePoint app or look for signage at the station explaining time or charge limits.

2. 2

   Start a new session

   After the session ends at 80%, you can often start a new session on the same charger to continue charging. Unplug, wait 10 seconds, plug back in, and authenticate again.

3. 3

   Check your car's own charge limit

   Some EVs have a default charge limit set to 80% in the car's settings. Check your car's infotainment system under charging settings. If the limit is set to 80%, the car itself is stopping the session, not ChargePoint.

4. 4

   Switch to a different station if you need to charge above 80%

   If the 80% cutoff is a station policy and you need more charge, find a station without this restriction. AC chargers at destinations are usually a better choice for topping up above 80% because DC charging is very slow above that level anyway.

Waitlist feature not working

ChargePoint offers a waitlist feature that is supposed to notify you when a busy charger becomes available. In practice, the notifications are unreliable, especially at European stations.

Symptoms

• You joined the waitlist but never received a notification
• The notification arrived long after the charger became available
• The waitlist button is not available for some stations
• You received a notification but the charger was already taken by someone else

How to Fix It

1. 1

   Enable push notifications for the ChargePoint app

   Go to your phone's notification settings and make sure ChargePoint notifications are allowed. On iOS, check Settings, then Notifications, then ChargePoint. On Android, check App Info, then Notifications.

2. 2

   Stay within a reasonable distance of the station

   The waitlist is most useful when you are nearby, at a shop or restaurant within a few minutes of the charger. By the time you drive 15 minutes back to a station, the charger may already be taken again.

3. 3

   Do not rely solely on the waitlist

   Treat the waitlist as a nice-to-have, not a guarantee. Check the app manually every few minutes for availability updates, or look for an alternative station while you wait.

4. 4

   Check if the station supports the waitlist feature

   Not all ChargePoint stations have the waitlist enabled, particularly CPO-operated stations using ChargePoint hardware. If you do not see a waitlist option on the station page, the feature is not available there.

App interface confusing for European users

ChargePoint's app was designed primarily for the US market. European users sometimes encounter US-centric defaults, unfamiliar terminology, or features that do not apply in Europe.

Symptoms

• App defaults to miles instead of kilometers
• Pricing displayed in unexpected formats or currencies
• Filter options include connector types not used in Europe, like NACS
• Station details reference US-specific payment methods or loyalty programs
• Map loads centered on the US instead of your actual location

How to Fix It

1. 1

   Set your region and units in the app settings

   Open the ChargePoint app, go to Account or Settings, and look for region, language, or unit preferences. Set distance to kilometers and currency to your local currency.

2. 2

   Filter for CCS2 connectors

   When searching for stations, use the filter to show only CCS2 (the European DC fast charging standard). This hides US-only connector types from your results.

3. 3

   Check the station detail for European pricing

   Tap on a station to see the pricing breakdown. European ChargePoint stations typically show pricing in EUR, SEK, NOK, or GBP per kWh, sometimes with an additional per-minute fee after a certain duration.

4. 4

   Ignore US-specific features

   Features like ChargePoint Home integration or certain fleet management tools are designed for the US market. If something in the app does not seem relevant, it probably is not meant for European users.

CPO-operated station behaves differently than expected

Some stations use ChargePoint hardware and appear in the ChargePoint app, but they are owned and operated by a local charge point operator. These stations may have different pricing, access rules, or session limits than ChargePoint-owned stations.

Symptoms

• Pricing at the station does not match what you expected from ChargePoint
• Your ChargePoint account works but the session has unexpected restrictions
• The charger looks like ChargePoint but has another company's branding on it
• Customer support refers you to a different company for this station

How to Fix It

1. 1

   Check who operates the station

   In the ChargePoint app, the station detail page usually shows the operator or network name. If it says something other than ChargePoint, the station is CPO-operated and may have its own rules.

2. 2

   Read the pricing and terms on the station detail page

   CPO-operated stations set their own pricing. Check the ChargePoint app for the exact per-kWh rate and any time-based fees or session limits before you plug in.

3. 3

   Try the CPO's own app if ChargePoint authentication fails

   Some CPO stations accept ChargePoint cards but work more reliably with the operator's own app or RFID card. Look for the operator's name on the charger and download their app.

4. 4

   Contact the station operator for site-specific issues

   For problems like broken hardware, pricing errors, or access restrictions at a CPO-operated station, contact the operator directly. Their contact information is usually on the charger or in the station detail in the ChargePoint app.