Audi e-tron GT Charging at K-Lataus

Audi e-tron GT Charger Won't Start Charging

You have plugged in your e-tron GT, but nothing happens. The MMI screen stays silent or shows an error. The e-tron GT has two charge ports, one on the left rear for AC and one on the right rear for DC, which can add confusion. This is frustrating, but it is almost always fixable on the spot.

Symptoms

• CCS2 or Type 2 connector plugged in but no charging indicator on the MMI touchscreen
• Charger screen shows 'Waiting for vehicle' or stays on the start screen
• e-tron GT charge port LED blinks but charging never begins
• Authentication succeeds on the charger but the session fails to start
• Plugged into the wrong charge port for the type of charging

What to Do

1. 1

   Verify you are using the correct charge port

   For DC fast charging, use the charge port on the right rear of the car. For AC charging with a Type 2 cable, use the charge port on the left rear. Using the wrong port is the most common cause of a failed start on the e-tron GT.

2. 2

   Check for a charging schedule or departure timer

   On the MMI touchscreen, go to the e-tron charging settings. If a timer or departure schedule is active, switch it to charge immediately or turn off the timer. You can also check the myAudi app for active schedules.

3. 3

   Unplug and reconnect firmly

   Remove the connector, wait 10 seconds, then reinsert it firmly into the correct charge port until you hear a clear click. Watch the charge port LED for a steady response.

4. 4

   Restart the charger session

   On the charger, end the current session if one is active. Then start a new session by tapping your RFID card, using contactless payment, or restarting in the charger operator's app.

5. 5

   Reboot the MMI system

   Press and hold the power button on the MMI touchscreen for about 10 seconds until the screen goes dark and restarts. Once it is back, try plugging in again. This resets the charging communication on the car's side.

6. 6

   Try a different charger

   If the station has multiple stalls, move to a different one. Some chargers have firmware issues that cause 800V handshake failures. A different unit at the same station may work fine.

Audi e-tron GT Charging Payment Failed at Station

You are at the charger, your e-tron GT is plugged in, but the payment will not go through. The charger shows an error or just sits there waiting. Payment failures at public chargers are common and usually have nothing to do with your car. Here is how to get charging.

Symptoms

• Charger displays 'Payment failed' or 'Authorization error' after tapping your card
• RFID card is not recognized by the charger's reader
• myAudi or Audi charging app shows an error when trying to start a remote session
• Plug & Charge does not activate after plugging in the CCS2 connector on the right rear
• Contactless payment terminal on the charger rejects your bank card

What to Do

1. 1

   Try a different payment method

   If your RFID card failed, try contactless with your bank card or phone. If contactless failed, try the charger operator's app. Having two or three payment options gives you the best chance of getting going.

2. 2

   Check the myAudi app

   Open the myAudi app on your phone. Make sure your Audi charging account is active, your payment method is valid, and Plug & Charge is enabled if you want to use it. Try starting the session remotely through the app.

3. 3

   Scan the charger's QR code

   Most public chargers have a QR code on the unit. Scanning it with your phone's camera opens the operator's payment page. You can usually pay with a credit card through the browser without downloading an app.

4. 4

   Check your bank app for blocked transactions

   Open your banking app and check for any flagged or blocked transactions. Some banks require you to approve the charge manually. If you see a notification, approve it and try the payment again.

5. 5

   Try Plug & Charge if available

   If the charger supports Plug & Charge and your e-tron GT has it activated through the myAudi app, simply unplug and replug the CCS2 connector into the right rear charge port. The payment should authorize automatically through the cable.

6. 6

   Move to a different charger

   If nothing works at this station, the charger's payment system may be down entirely. Find a nearby alternative using the myAudi app or the e-tron GT's built-in charger finder on the MMI touchscreen.

Audi e-tron GT Charging Slower Than Expected

You plugged in your e-tron GT expecting 270 kW and the MMI touchscreen shows 50 kW. With an 800V architecture designed for ultra-fast charging, this is especially frustrating. Slow charging on the e-tron GT is almost never a defect. It is usually the charger's capability, the battery temperature, or a mismatch between the station's voltage and the car's 800V system.

Symptoms

• DC fast charging speed well below the 270 kW maximum shown on the MMI touchscreen
• AC home charging stuck at 3-4 kW instead of the full 11 kW or optional 22 kW
• Charging speed drops significantly after reaching 50-60% state of charge
• The e-tron GT charges at similar speeds to 400V vehicles despite having 800V architecture
• MMI display shows lower power than the charger's rated output

What to Do

1. 1

   Verify the charger supports 800V and high power

   Check the charger's label or the operator's app for the maximum power output and voltage. For the e-tron GT to reach its peak 270 kW, you need a charger rated for at least 270 kW at 800V. A 150 kW or 400V charger will work but at much lower speeds.

2. 2

   Check the battery temperature

   Look at the charging screen on the MMI touchscreen. If the battery is cold, use the navigation system to route to the fast charger. The e-tron GT will precondition the battery on the way using its heat pump. If you are already at the charger, driving for 15-20 minutes and returning can help.

3. 3

   Check your state of charge

   Look at the digital instrument cluster or MMI screen. If you are above 80%, the slower speed is expected. For the fastest charging, arrive at the charger between 5-20% and charge to 80%.

4. 4

   Verify the charger is not sharing power

   Look at the charger unit. If there are two cables and someone is using the other one, you may be sharing power. Move to an unoccupied charger if one is available.

5. 5

   Check the AC charge current setting

   On the MMI touchscreen, go to the e-tron charging settings. Make sure the AC charge current is set to maximum. If you have the optional 22 kW onboard charger, verify your wallbox supports it.

6. 6

   Try a different charger

   If the speed is still low, the charger itself may be degraded or faulty. Look for Ionity, Electrify America, or other 350 kW networks that support 800V to get the best speeds from your e-tron GT.

Session fails to start or charger shows an error

The charger does not begin charging after you plug in and authenticate. This can happen due to communication issues between your vehicle and the charger, or a problem with authentication.

Symptoms

• You plug in and authenticate but the charger displays an error
• The charger screen stays on the welcome screen and does not proceed
• The app shows 'session starting' but nothing happens at the charger
• The connector locks but no power flows

How to Fix It

1. 1

   Unplug, wait 30 seconds, and try again

   The initial communication handshake between your vehicle and the charger sometimes fails. Unplug the connector, wait at least 30 seconds, and reconnect. The second attempt often works.

2. 2

   Try starting the session from the K-Lataus app

   If RFID authentication is not working, open the K-Lataus app, select the station and charger, and start the session through the app instead.

3. 3

   Try a different charger unit at the same station

   If the station has multiple charger units, switch to another one. One unit may have a hardware issue while the others work fine.

4. 4

   Check that your vehicle is ready to charge

   Make sure your vehicle is not in a state that prevents charging, such as a charging schedule being active, the charge port not fully engaged, or a vehicle-side error. Check your vehicle's dashboard for any warnings.

Setting up the K-Lataus app for the first time

K-Lataus has its own dedicated app. First-time setup requires a K-Group account and a payment method linked specifically to the K-Lataus service.

Symptoms

• You are not sure which app to use for K-Lataus charging
• Your K-Group login works on the K-Group website but not in the K-Lataus app
• You cannot find a way to add a payment method for charging
• You cannot find the K-Lataus app in your app store

How to Fix It

1. 1

   Install the K-Lataus app

   Search for 'K-Lataus' in the App Store or Google Play and install it. This is the dedicated app for K-Lataus EV charging. K-Ruoka is for groceries, not for charging.

2. 2

   Log in with your K-Group credentials

   Use the same K-Group username and password you use for other K-Group services. If you do not have a K-Group account yet, you can create one in the app.

3. 3

   Add a payment method in the K-Lataus app

   Go to payment settings in the K-Lataus app and add a credit or debit card. The K-Lataus app manages its own payment methods separately from other K-Group services.

4. 4

   Find a station and start your first session

   Use the map in the K-Lataus app to find a nearby station. Plug in your vehicle, then tap Start in the app or use an RFID card to begin charging.

Parking time limits at grocery store locations

K-Lataus chargers sit in K-Citymarket and K-Market parking lots, which often have monitored parking with time limits. You may get a parking notice if you stay too long.

Symptoms

• You see parking time limit signs (e.g. 2 or 3 hours) in the parking lot
• You received a parking notice even though you were charging
• Your charging session takes longer than the allowed parking time
• Camera-monitored parking is active in the lot

How to Fix It

1. 1

   Check the parking rules when you arrive

   Most K-Citymarket and K-Market parking lots have posted time limits, often 2 to 4 hours, enforced by camera monitoring or a parking operator. These rules apply to EV charging spots too.

2. 2

   Use a parking disc if required

   Many Finnish parking lots still require a parking disc (pysäköintikiekko). Set the arrival time and display it on your dashboard, even if the lot also has camera monitoring.

3. 3

   Set a phone timer to move your car

   If you are shopping while charging, set an alarm so you can return before the parking limit expires. A DC fast charger at 200 kW should get you a substantial charge well within a 2-hour window.

4. 4

   Unplug when charging is complete

   Do not leave your vehicle occupying the charging spot after it finishes. Other EV drivers need the spot, and some parking operators treat finished-but-still-connected vehicles as overstaying.

New stations not appearing in third-party apps

K-Lataus is expanding its network, but newer stations sometimes take weeks to appear in third-party apps and aggregators like PlugShare or Google Maps.

Symptoms

• The K-Lataus app shows a station that does not appear in PlugShare or ABRP
• You planned a route using a third-party app and it skipped a nearby K-Lataus station
• A station listed as 'coming soon' in the K-Lataus app is actually already operational
• Google Maps does not show K-Lataus chargers at a location where you know they exist

How to Fix It

1. 1

   Use the K-Lataus app as the primary source for station locations

   The K-Lataus app is always the most up-to-date source for K-Lataus stations. Third-party apps rely on data feeds that may lag behind actual station openings by days or weeks.

2. 2

   Cross-check with the K-Lataus website

   The K-Lataus website also maintains a station map. Check it if the app is not giving you the information you need or if you want to plan ahead on a larger screen.

3. 3

   Report missing stations to third-party apps

   If you use PlugShare or ABRP regularly, you can add missing stations yourself. This helps other EV drivers find K-Lataus locations that are not yet in the database.

4. 4

   For route planning, combine K-Lataus with other network apps

   When planning a longer trip, check the K-Lataus app alongside ABRP or a similar route planner. The K-Lataus app shows the latest stations, while the route planner optimizes your overall charging stops across all networks.

Slow charging or failed sessions at older units in winter

Some older K-Lataus charger units perform less reliably in extreme cold. Winter in Finland brings temperatures that can affect both the charger hardware and your vehicle's battery.

Symptoms

• The charger takes a long time to initialize in freezing conditions
• Session fails with a generic error after a long handshake attempt
• Charging speed is much lower than expected at a 200 kW station
• The charger screen is slow to respond or displays incorrectly in cold weather

How to Fix It

1. 1

   Precondition your battery before arriving

   If your vehicle has a battery preconditioning feature (most newer EVs do), activate it before arriving at the charger. A warm battery accepts power faster and communicates more reliably with the charger during the initial handshake.

2. 2

   Try unplugging and reconnecting

   In cold weather, the initial handshake between your vehicle and the charger can time out. Unplug, wait 30 seconds, and try again. Sometimes the second attempt connects cleanly.

3. 3

   Try a different charger unit at the same station

   If the station has multiple charger units, one may be more reliable than the other. Older units can have more cold-weather issues than newer installations.

4. 4

   Report consistently problematic chargers

   If a specific charger unit fails repeatedly in cold weather, report it through the K-Lataus app. This helps K-Group identify hardware that needs maintenance or replacement.

5. 5

   Accept that cold weather reduces charging speed

   Even when everything works perfectly, a cold battery charges slower. This is a physics limitation, not a charger fault. The first 10 to 15 minutes of a session may be slower until the battery warms up from the charging current itself.