Peugeot e-Expert Charging at EnBW mobility+

Peugeot e-Expert Charger Will Not Start Charging

You plugged in the CCS2 cable but the charger just sits there doing nothing. Or you tapped your RFID card and the screen showed an error. When you have deliveries waiting, a charger that will not start is the last thing you need. Most start failures on the e-Expert come down to authentication, cable seating, or the charger itself.

Symptoms

• CCS2 connector plugged in but charger shows no active session
• Charger displays an error code after tapping RFID card or using the app
• Dashboard shows the charge port is connected but charging does not begin
• Cable does not lock into the CCS2 port on the e-Expert
• Charger starts authorization but times out without delivering power

What to Do

1. 1

   Remove and reseat the CCS2 connector

   Pull the connector out completely, wait 10 seconds, and push it back in firmly until you hear or feel a click. Make sure the charge port flap is fully open and the port is clean.

2. 2

   Check for a charging schedule

   On the e-Expert's touchscreen, go to charging settings. If a schedule is active, disable it or select the option to charge immediately.

3. 3

   Re-authenticate with the charger

   End any active session in the charging app, then start a new one. If using RFID, hold the card steady against the reader for a few seconds. Some chargers need authentication before you plug in.

4. 4

   Clean the charge port

   If the connector feels loose or does not click, check the charge port for dirt, ice, or debris. Wipe it out with a dry cloth. Commercial vans pick up more road grime than passenger cars.

5. 5

   Try a different stall or charger

   If the charger has multiple stalls, try another one. If none work at this location, move to the next charger on your route. Do not spend too much time on a single faulty charger.

6. 6

   Restart the vehicle systems

   Turn the e-Expert fully off, wait 30 seconds, then turn it back on. Unplug and replug the cable. This resets the charging communication between the van and the charger.

Peugeot e-Expert Charging Payment Failed at DC

You tapped your card, the charger showed a red X, and now you are stuck. Payment failures at public chargers are not about your e-Expert. They are about the charging network, your payment method, or your phone signal. Here is how to troubleshoot and get back on your delivery route.

Symptoms

• Charger displays a payment error or 'transaction declined' message
• Charging app shows 'session failed to start' after payment
• RFID card is not recognized by the charger reader
• Contactless bank card tap does not register on the charger
• Authorization process starts but times out before power is delivered

What to Do

1. 1

   Try a different payment method

   If RFID failed, try the app. If the app failed, try a contactless bank card. Having multiple options means one failure does not ruin your charging stop.

2. 2

   Check your mobile signal

   Look at your phone's signal bars. If signal is weak, the app cannot complete the transaction. Try stepping away from structures that block signal.

3. 3

   Verify payment details in the app

   Open the charging app and check your payment method. Make sure the card has not expired and there are no outstanding issues. Update if needed.

4. 4

   Check accepted networks on the charger

   Look for logos or stickers showing which charging networks and apps are accepted. If yours is not listed, you need a different app or card with roaming access.

5. 5

   Contact your fleet manager or card provider

   If using a company-provided RFID card, it may be deactivated or restricted to certain networks. Contact your fleet manager. Most RFID cards have a support number printed on them.

6. 6

   Move to a nearby alternative charger

   If payment will not work at this charger, check your app for the next closest option on your route. Do not lose too much time troubleshooting a single station.

Peugeot e-Expert Charging Slower Than Expected

You stopped for a mid-route charge and the screen shows 25 kW instead of the 100 kW maximum. The e-Expert's 75 kWh battery is larger than most vans on the Stellantis platform, which means longer charge times if something is limiting the speed. Slow charging is almost never a defect. It is usually the battery temperature, state of charge, or the charger itself.

Symptoms

• DC fast charging speed well below the 100 kW maximum
• AC depot charging stuck at 3-4 kW instead of the full 11 kW
• Charging speed drops sharply after reaching 50-60% on the dashboard
• Charging session starts at a reasonable speed but drops quickly within minutes
• Charger display shows lower power output than its rated capacity

What to Do

1. 1

   Check the battery temperature

   Look at the dashboard or the MyPeugeot app for battery temperature information. If the battery is cold, driving for 20-30 minutes before charging helps. The e-Expert does not precondition the battery, so plan your first charging stop after some time on the road.

2. 2

   Check your state of charge

   Look at the battery percentage on the dashboard. If you are above 80%, the slower speed is normal. For the fastest DC charging on your route, arrive between 10-20% and unplug at 80%.

3. 3

   Verify the charger is not sharing power

   Look at the charger unit. If there are two cables and another vehicle is using the other one, you may be sharing power. Move to an unoccupied charger if available.

4. 4

   Check the AC charge current setting

   On the e-Expert's touchscreen, go to the charging settings and make sure the AC charge current is set to maximum. A reduced setting will limit your depot or home charging speed.

5. 5

   Confirm your depot wallbox phase configuration

   Ask your facility manager or electrician to verify the wallbox is wired for 3-phase power. Single-phase limits you to about 3.7 kW, meaning over 20 hours for a full charge on the 75 kWh battery.

6. 6

   Try a different charger

   If the DC speed is still low, the charger may be degraded or faulty. Try a different stall at the same location or a different charging station on your route.

Roaming pricing unclear or higher than expected

You started a session through EnBW mobility+ and the per-kWh price was significantly higher than you expected. The same charger costs different amounts at different times, and the pricing logic feels opaque.

Symptoms

• Per-kWh rate on the receipt is higher than the rate shown on the EnBW website
• Same charger location costs more through EnBW mobility+ than through the CPO's own app
• Price differs between two chargers at the same station
• Unexpected 'roaming fee' or 'session fee' on your invoice

How to Fix It

1. 1

   Check the price before you start the session

   In the EnBW mobility+ app, tap on the charger and look for the pricing details before starting. The app shows the per-kWh rate for that specific charger. Prices vary because each CPO sets different roaming rates.

2. 2

   Understand the pricing tiers

   EnBW mobility+ groups chargers into pricing tiers. 'EnBW own' chargers are cheapest, 'roaming standard' is mid-range, and 'roaming plus' (typically high-power chargers from premium CPOs like Ionity) costs more. The tier is usually shown in the charger details.

3. 3

   Compare with the CPO's own app

   If a charger is operated by Ionity, for example, check the Ionity app or website for their direct pricing. Sometimes the CPO's own app or RFID card is cheaper because there is no roaming middleman. If you use that CPO frequently, their own account may save you money.

4. 4

   Consider the EnBW mobility+ tariff you are on

   EnBW offers different tariffs (with and without a monthly fee). The tariff with a monthly fee usually gives lower per-kWh rates. In the app, go to your profile to check which tariff you are on and whether switching would save you money based on your usage.

5. 5

   Watch for idle fees and blocking fees

   Some chargers accessed through EnBW mobility+ charge a per-minute fee after your car finishes charging but the cable is still plugged in. Move your car promptly once charging is complete to avoid these fees.

App not loading charger details

You tap on a charger pin on the map and the detail screen is blank, shows a loading spinner forever, or displays outdated information. You cannot see pricing, availability, or the start button.

Symptoms

• Charger detail page shows a permanent loading spinner
• Availability status not updating (shows 'Available' for hours at a busy station)
• Price information missing from the detail screen
• App shows 'No connection' error when loading charger details

How to Fix It

1. 1

   Check your phone's internet connection

   Charging stations are often in areas with poor cellular coverage, like parking garages, highway rest stops behind concrete walls, or rural areas. Switch between mobile data and Wi-Fi, or walk to a spot with better signal and load the charger details there.

2. 2

   Force-close the app and reopen it

   Swipe the EnBW mobility+ app away from your recent apps list, wait a few seconds, and reopen it. Navigate to the charger again. This clears any stuck network requests.

3. 3

   Search for the charger by ID

   Instead of tapping the map pin, use the search bar in the app and enter the charger's ID or EVSE number (printed on the physical unit). This sometimes loads details that the map view fails to fetch.

4. 4

   Use the QR code on the charger as a backup

   Many chargers have a QR code that opens a direct session start page. Scan it with your phone camera. This page is served by the CPO, not EnBW, and often loads faster.

5. 5

   Clear the app cache

   On Android: Settings, Apps, EnBW mobility+, Storage, Clear Cache. On iOS: delete and reinstall the app (iOS does not offer cache clearing). This resolves issues caused by corrupted local data.

QR code scan not working

You scan the QR code on the charger with the EnBW mobility+ app and it either does not recognize the code, opens a wrong page, or shows an error.

Symptoms

• App says 'QR code not recognized' after scanning
• QR code opens a web page for the CPO's own app instead of EnBW mobility+
• Camera does not focus on the QR code (too dark, code damaged)
• Scan succeeds but the session start page shows an error

How to Fix It

1. 1

   Use the EnBW app's built-in scanner, not your phone camera

   Open the EnBW mobility+ app and use its QR scanner (usually in the top menu or via a scan button on the map screen). Scanning with your phone camera might open the CPO's own page instead of routing through EnBW.

2. 2

   Clean the QR code

   Wipe dirt, rain, or ice off the QR code with your sleeve. Damaged or faded QR codes are common on outdoor chargers. If the code is badly worn, look for a second QR code on a different part of the charger.

3. 3

   Turn on your phone's flashlight

   In dark or shaded areas, the camera cannot read the code. Most QR scanners (including EnBW's) have a flashlight toggle. Enable it for better readability.

4. 4

   Enter the charger ID manually

   If the QR code will not scan, look for the charger's numeric or alphanumeric ID printed nearby. Enter it manually in the EnBW app's search function to find and start the session.

Cannot stop the session from the app

You tap 'Stop Charging' in the EnBW mobility+ app and nothing happens. The session keeps running, your car keeps charging (or has already finished but the session stays active), and you want to unplug and leave.

Symptoms

• 'Stop' button in the app does not respond or shows an error
• Session shows as active in the app even after unplugging
• Charger screen says 'Session active' but your car is full
• You are worried about accumulating idle fees

How to Fix It

1. 1

   Physically unplug the connector from your car

   On most chargers, unplugging the cable ends the session automatically, regardless of what the app says. Unlock your car's charge port (from the car's screen, key fob, or charge port button) and remove the connector.

2. 2

   Wait 2 minutes and check the app again

   There is often a delay between physically ending the session and the app updating. The app depends on the CPO's system sending a 'session ended' signal back through the roaming chain. Give it a moment.

3. 3

   Force-close and reopen the app

   Sometimes the app's session view gets stuck. Force-close it, reopen, and check your session history. The session may already be ended on the backend even if the active session screen was not updating.

4. 4

   Press the stop button on the charger itself

   Many chargers have a physical stop button on the screen or housing. Press it. This sends the stop command directly to the charger hardware without going through the roaming network.

5. 5

   Contact support if you are being billed for a stuck session

   If the session stays 'active' in the app for more than 10 minutes after you have unplugged and driven away, contact EnBW mobility+ support. They can close the session on their end and correct any overcharges.

App is in German and hard to navigate

The EnBW mobility+ app defaults to German. If you do not speak German, navigating menus, understanding pricing details, and finding settings can be frustrating.

Symptoms

• All menus and buttons are in German after installation
• Language setting not obvious in the app
• Error messages appear in German, making troubleshooting difficult
• Pricing terms and tariff explanations are only in German

How to Fix It

1. 1

   Change your phone's system language temporarily

   The EnBW mobility+ app follows your phone's system language. If English is available in the app, switching your phone to English (Settings, General, Language) will switch the app too. You can switch back after you finish.

2. 2

   Check for an English option in the app settings

   Open the app, tap the profile or menu icon (usually three lines or a person icon in the corner), and look for 'Sprache' (Language) or 'Einstellungen' (Settings). Some versions offer English as an option directly.

3. 3

   Use your phone's translate feature on screenshots

   On iOS, take a screenshot and use Live Text to translate. On Android, use Google Lens. This is useful for understanding pricing details or error messages in German.

4. 4

   Consider an alternative roaming app with better language support

   If the language barrier is a persistent problem, apps like Shell Recharge, Plugsurfing, or Chargemap offer similar roaming coverage across Europe and have full English interfaces. They access many of the same chargers.