Hyundai IONIQ 5 Charging at Shell Recharge

Hyundai IONIQ 5 Charger Will Not Start a Charging Session

You have plugged the cable into your IONIQ 5's charge port on the right rear fender, but nothing is happening. No power flowing, no charging animation on the cluster. This is frustrating, but it is rarely the car. Most failed charging starts come from the charger, the app, or a setting on the vehicle. Here is how to work through it.

Symptoms

• Charge port light does not turn on or blinks red after plugging in
• Charger screen shows an error or returns to the start screen immediately
• Charging app shows session failed or authentication error
• Cable is plugged in but the IONIQ 5 does not recognize the connection
• Charge port door will not open, especially in cold weather

What to Do

1. 1

   Open the charge port door

   Press the button on the charge port door on the right rear fender. If it will not open in cold weather, try pressing and holding the unlock button on your key fob, or gently warm the edges with your hands or lukewarm water. Do not force it open or use sharp tools.

2. 2

   Check for scheduled charging

   On the center touchscreen, go to EV settings and check if a charging schedule is active. You can also check in the Bluelink app under the charging section. Disable the schedule temporarily to charge immediately.

3. 3

   Unplug and reconnect the cable firmly

   Remove the cable completely, wait 10 seconds, and plug it back in. Push the CCS2 connector in until it clicks into the charge port. Make sure both the upper (AC) and lower (DC) sections are fully seated.

4. 4

   Re-authenticate at the charger

   Tap your RFID card again, restart the charging app, or try a different payment method. If the charger supports Plug and Charge and your IONIQ 5 has it enabled, try unplugging and replugging to re-trigger automatic authentication.

5. 5

   Try a different charger or stall

   If the session still will not start, the charger may be faulty. Move to a different stall at the same station. If all stalls fail, try a different charging station entirely.

6. 6

   Restart the car if needed

   In rare cases, the IONIQ 5's charging system needs a reset. Unplug the cable, sit in the car, press the start button to turn the car on, wait 30 seconds, turn it off, and try plugging in again.

Hyundai IONIQ 5 Charger Payment or Authentication Failed

You are at the charger, cable in hand, and the screen says payment failed or authentication error. Your IONIQ 5 is ready to charge, but the charger will not let you start. This is almost always a charger-side or app-side issue, not a car problem. Here is how to get charging.

Symptoms

• Charger screen shows payment declined or authentication error
• RFID card is not recognized when tapped on the reader
• Charging app shows session failed to start or payment error
• Contactless bank card is declined at the charger terminal
• Plug and Charge does not auto-authenticate after plugging in

What to Do

1. 1

   Check your charging app account

   Open your charging app and verify that your payment method is valid, your balance is sufficient (for prepaid accounts), and there is no stuck session from a previous charge. Update your payment method if the card on file has expired.

2. 2

   Try a different authentication method

   If your RFID card failed, try the app's QR code or start-via-app feature. If the app failed, try tapping your RFID card. If you have a contactless bank card, try that. Having at least two methods available saves time.

3. 3

   Check if Plug and Charge is enabled

   On the center touchscreen, go to EV settings and look for the Plug and Charge option. Make sure it is turned on. Then check if the charging network supports Plug and Charge. If both are set up, unplug the CCS2 cable and plug it back in to re-trigger authentication.

4. 4

   Restart the charger if possible

   Some chargers have a reset option on the screen or a physical button. If the charger seems stuck from a previous session, restarting it can clear the error. Check the charger screen for a reset or cancel option.

5. 5

   Move to a different charger

   If authentication keeps failing on one charger, try a different stall at the same station. Charger hardware varies even within the same location, and another unit may process your payment without issues.

6. 6

   Contact the charging network's support

   Most chargers display a phone number or support contact on the screen or on a sticker. Call or message the network's support to report the issue. They can sometimes remotely start a session or clear a stuck charger from their side.

Hyundai IONIQ 5 Charging Slower Than Expected at DC or AC

Your IONIQ 5 has one of the fastest charging architectures on the market. 800V, up to 233 kW, 10-80% in roughly 18 minutes. So when the screen shows 50 kW at a fast charger, something feels wrong. In most cases, slow charging on the IONIQ 5 is not a defect. It is usually the battery temperature, the charger's actual output, or a setting worth checking.

Symptoms

• DC fast charging speed well below the 233 kW maximum
• AC home or destination charging stuck at 3-4 kW instead of 11 kW
• Charging speed drops sharply after reaching 60-70%
• Charging session starts at low power and never ramps up
• Instrument cluster shows much lower power than the charger's rated output

What to Do

1. 1

   Check the battery temperature on the cluster

   Look at the charging information on your 12.3-inch instrument cluster or center touchscreen. If the battery temperature is low, consider driving for 15-20 minutes before your next charging stop, or use the built-in navigation to trigger battery preconditioning automatically.

2. 2

   Confirm the charger supports 800V

   Check the charger's specifications on its screen or the charging network's app. If it is a 400V charger, the IONIQ 5's multi-charging system will still work, but speeds will be lower than on an 800V unit. No adapter needed.

3. 3

   Check your state of charge

   If you are above 80%, the slowdown is expected. For the fastest road trip charging, plan stops so you arrive between 10-20% and unplug at 80%.

4. 4

   Check scheduled charging and charge limits

   Open the EV settings on the center touchscreen or in the Bluelink app. Make sure scheduled charging is not active (it can delay charging start) and the charge current limit is set to maximum.

5. 5

   Verify the charger is not sharing power

   Look at the charger unit. If two cables come from the same cabinet and someone is using the other one, you may be splitting power. Move to an unoccupied charger if available.

6. 6

   Try a different charger or station

   If the speed is still low after checking everything, the charger itself may be degraded or throttled. Try another stall at the same location, or head to a different station entirely.

RFID card not recognized at the charger

You tap your Shell Recharge RFID card on the charger's reader but it does not respond, beeps an error, or shows 'Card not recognized.'

Symptoms

• Charger beeps but displays 'Unknown card' or 'Authorization failed'
• No response at all when tapping the card
• Card works at some stations but not others
• Card worked yesterday at the same charger but does not work today

How to Fix It

1. 1

   Hold the card still on the reader for 3 to 5 seconds

   RFID readers at some chargers are slow. Do not tap and remove quickly. Hold the card flat against the reader and wait for a confirmation beep or screen change.

2. 2

   Check that your RFID card is activated

   New Shell Recharge RFID cards must be activated in the Shell Recharge app before first use. Go to the app, find the RFID section, and make sure the card status shows active.

3. 3

   Try starting the session through the app instead

   Open the Shell Recharge app, find the station, select the charger, and start the session digitally. This bypasses the RFID reader entirely and uses the roaming connection.

4. 4

   Check if the CPO supports Shell Recharge roaming

   Not every charger that appears in the Shell Recharge app accepts the Shell Recharge RFID card. Some chargers only accept app-based roaming. The station details in the app usually indicate which payment methods are supported.

5. 5

   Clean the card and try again

   Dirt, scratches, or a phone case between the card and reader can block the RFID signal. Remove the card from any holder, wipe it, and try again on the reader's sweet spot (often marked with a contactless symbol).

Roaming vs direct pricing confusion

The price you pay through Shell Recharge is different from the price shown on the charger's screen. This is because Shell Recharge adds a roaming markup on top of the CPO's base rate.

Symptoms

• Charger screen shows 0.39 EUR/kWh but Shell Recharge bills 0.55 EUR/kWh
• Invoice includes fees not displayed at the charger (session fee, per-minute fee)
• Same station is cheaper when using the CPO's own app
• Pricing in the Shell Recharge app does not match the final invoice

How to Fix It

1. 1

   Check the Shell Recharge app for the roaming price before starting

   Before you tap your card or start a session, open the Shell Recharge app and select the station. The app shows the Shell Recharge price, which includes any roaming fee. This is the price you will actually pay.

2. 2

   Understand the pricing structure

   Shell Recharge typically charges a per-kWh rate plus sometimes a session start fee or per-minute fee. The charger screen shows the CPO's direct price, not the roaming price. These are two different rates for two different billing relationships.

3. 3

   Consider using the CPO's own app for lower rates

   If you charge at the same network regularly (for example, Allego, Fastned, or EnBW), their own app usually offers a lower price than roaming through Shell Recharge. The trade-off is managing multiple apps.

4. 4

   Download your invoice from the Shell Recharge app

   Go to your charging history in the Shell Recharge app. Each session has a detailed breakdown showing energy delivered, per-kWh rate, session fees, and total cost. Compare this with what you expected.

Session not starting via QR code

You scan the QR code on the charger to start a session through the Shell Recharge app, but nothing happens or you get an error.

Symptoms

• QR code opens the Shell Recharge app but shows 'Station not found'
• QR code opens a web page instead of the app
• App shows 'Unable to start session' after scanning
• QR code is faded, damaged, or partially covered by a sticker

How to Fix It

1. 1

   Search for the station manually in the app

   If the QR code does not work, open the Shell Recharge app, search for the station by name or location, and start the session from the station page. You may need to select the specific connector or charger ID.

2. 2

   Check the charger ID number

   Every charger has an ID printed somewhere on the unit (usually near the QR code or on a label). Enter this ID manually in the Shell Recharge app if the QR scan fails.

3. 3

   Make sure the QR code belongs to Shell Recharge

   Many chargers have multiple QR codes from different roaming providers and the CPO itself. Make sure you are scanning the Shell Recharge QR code, not the CPO's own code. Scanning the wrong code opens the wrong app or website.

4. 4

   Try the RFID card or contactless payment instead

   QR code start is just one method. Tap your Shell Recharge RFID card or use contactless payment if the charger supports it.

5. 5

   Check your internet connection

   Starting a session via QR code requires the app to communicate with Shell Recharge's servers and the CPO's backend. If you have weak mobile signal (common at highway rest stops), the request may time out. Try switching between Wi-Fi and mobile data.

App showing wrong charger status

The Shell Recharge app shows a charger as available, occupied, or offline, but the actual status is different when you arrive.

Symptoms

• App shows 'Available' but the charger is out of order or has an error screen
• App shows 'Occupied' but no vehicle is connected
• Status has not updated for hours and seems stale
• App shows fewer chargers at a station than physically exist

How to Fix It

1. 1

   Understand that status data is delayed

   Shell Recharge gets charger status from the CPO's systems through the roaming connection. This data can lag by 5 to 15 minutes. A charger that just became available may still show as occupied in the app.

2. 2

   Try plugging in regardless of app status

   If you are already at the station and a charger looks physically available (no vehicle connected, no error on screen), try plugging in and starting a session. The real-time status at the charger overrides whatever the app shows.

3. 3

   Check the CPO's own app for more accurate status

   The CPO (the company that actually operates the charger) usually has more accurate real-time status than roaming aggregators like Shell Recharge. If accuracy matters, cross-check with the CPO's app or website.

4. 4

   Report the incorrect status

   Use the Shell Recharge app to report the charger issue. This helps improve status accuracy over time.

Billing discrepancy between Shell Recharge and the CPO

The amount billed by Shell Recharge does not match what you expected based on the energy delivered or the session duration. This can happen because of how roaming billing works.

Symptoms

• Billed for more kWh than your vehicle's dashboard shows
• Charged a session fee you did not expect
• Per-minute idle fee added even though you unplugged on time
• Double charge: both Shell Recharge and the CPO billed you

How to Fix It

1. 1

   Compare the Shell Recharge invoice with your vehicle's data

   Your vehicle's dashboard shows how much energy the battery received. The charger meters how much energy it delivered, which includes conversion losses. A 5 to 10% difference is normal.

2. 2

   Check for per-minute fees

   Some CPOs charge a per-minute fee (for time spent connected) on top of the per-kWh fee. This can be especially costly during slow AC charging sessions. Check the pricing breakdown in the Shell Recharge app.

3. 3

   Look for session or start fees

   Some stations add a fixed fee per session (for example, 0.35 EUR to 1.00 EUR). This appears in the Shell Recharge invoice as a separate line item.

4. 4

   Dispute the charge through the Shell Recharge app

   If the amount is clearly wrong (double billed, charged for a session that never started, or obviously excessive), contact Shell Recharge support through the app. Go to your charging history, select the session, and use the dispute or help option.

5. 5

   Keep your vehicle's charge data as evidence

   Take a photo of your vehicle's charging screen or dashboard showing the kWh received and the session duration. This is useful if you need to dispute a charge.